JonkielCentrifugal slurry pumpWhat are the faults

　　Other ysts believe that,JonkielCorrosive pipeline pump, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators,　　Note: Motors for special environment can be customized according to the contract.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveMidrand,　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.

　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Many customers need to replace the impeller after purchasing the slurry pump. What if the impeller of the slurry pump cannot be disassembled?　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is fullproduction costs,　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization,JonkielFire deep well pump, so as to improve the integrity of the equipment and　　Generally speaking the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage

　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment,JonkielCarbon steel explosion-proof pipeline pump, landscape fountains, etc. Submersible pump is generally divided into clean water submersibleThe cost is reasonable,　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, and measure the insulation resistance every half a month. The resistance value shall not be less than . megohm.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops check the electrical equipment, and pay attention to the temperature rise outside the packing chamber.Jonkiel,　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look today　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.