MilanFloor to floor cargo elevatorHow to perform preventive maintenance

Are the water cooling and air cooling of the hydraulic station the same?The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Milan,Novice operation: Since novices do not know much about mobile lifts and other aerial work platforms, or do not understand the operation method, they are prone to misoperation and cause equipment failure. Operators in this area need to study patiently and pass the training before they can operate and use.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Rakovski,Test the freight elevator every day to see if the freight elevator can operate normally.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, it may cause lifting failure in light cases, or electric shock accidents in severe cases.

Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.The one-way valve is damaged. The one-way valve is to prevent the oil from returning. If there is a problem, there will be some backflow, so it can be replaced with a new one at this time.Are the water cooling and air cooling of the hydraulic station the same?Economic management,MilanProduction of lifting cargo elevators,Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.

Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply,MilanElevating cargo elevator, and diesel engine.Cleaning and keeping it clean is the first priority. Regularly clean up the dust or sundries on the motor of the hydraulic lifting platform, otherwise the long-term accumulated dust will fall into the motor fan, and it will be very difficult to run, just like the laptop we usually use. If the dust on the computer fan is not cleaned, the computer will not be easy to dissipate heat, or even buzz. It will be much better after cleaning, and the same is true for the motor of the hydraulic lifting platform. V or V; how to properly maintain the motor of the hydraulic lifting platform to avoid the motor of course, it is safer to keep away from the water for things related to electricity, do not use it outdoors in rainy and snowy weather, etc., and pay attention to the selection during storage The environment is clean and dry; it is strictly forbidden to overload the hydraulic lifting platform. When using the hydraulic lifting platform, it must not be overloaded, which will bring a burden to the motor, and it may burn out the motor; At this time, you may wish to consult the manufacturer about the overload protection device. The overload protection device is generally selected by the manufacturer. After adding this device, you don’t have to worry about whether it is overloaded during use. It is not too expensive to add this device. Safe more at ease); can not adjust the overflow valve (also known as 'solenoid valve')Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Milan,Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the lifting of parts during the assembly of large equipment and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting,MilanChain guide rail lifting cargo elevator, fixed three-dimensional parking and other places.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, hydraulic lifting platforms are more widely used.