GroningenPrice of hydraulic platform lift truckWhat is the defect processing method

The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, clean the filter and add new oil after using a new filter element.Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than %.Groningen,When the hydraulic cargo elevator needs to work, first connect the power supply and press the button to drive the motor of the hydraulic power unit to drive the gear pump. The hydraulic oil forms a certain pressure through the vane pump and passes through the oil filter; Explosion proof electromagnetic directional valve; Throttle valve; Hydraulic control one-way valve; The balance valve enters the lower end of the hydraulic cylinder, causing it to move upwards and lift heavy objects. The hydraulic cylinder moves downwards (i.e. the weight drops), the explosion-proof electromagnetic directional valve of the hydraulic oil enters the upper end of the hydraulic cylinder, and the return oil from the lower end of the hydraulic cylinder passes through the balance valve; Hydraulic control one-way valve; Throttle valve, explosion-proof electromagnetic directional valve.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance,GroningenHydraulic lifting table small, cleaning, and replace the cleaning hydraulic oil to clean.Zaihran,When using hydraulic elevators, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift). Road noise can also occur if tires are crushed against objects that are prone to noise. The shaking amplitude of the scissor type lifting platform is proportional to its lifting height. The higher the height, the greater the shaking. When using it at a working height of meters, if possible, please use safety protection measuresThere is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.

The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.Oil pipe leaks oil. Poor sealing of oil pipes, resulting in a decrease in pressure and a natural descent of hydraulic cargo elevators. It is recommended to carefully check whether the oil pipes are intact and undamaged.The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn, the spring of the overflow valve is fatigued and deformed, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn,GroningenHydraulic cylinder lifting platform, it should be replaced.Pursuit of excellence,GroningenHydraulic lifting platform,Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.Lifting mechanism: The workbench should be ensured to rise and fall smoothly and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving, and there should be no leakage at all components, pipelines, and joints. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed repair or replace the spring, reduce the flow of the remote control port replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.

Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than %.Application process,When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shakingWhat are the requirements for the pit? This type of cargo elevator only needs - centimeters and does not require too much space. The installation of scissor type hydraulic cargo elevators is different from that of guide rail type hydraulic cargo elevators. The scissor lift cargo elevator has a large load-bearing capacity, and the pit depth needs to be set at around - centimeters. It can also be designed according to customer on-site needs.There are many reasons for unstable workbench descent, such as overload, unstable support severe eccentric load, hydraulic oil impurities, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.Groningen,An inverter can also generate high noise. When the power supply voltage is lower than % of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.