Kolchin Wear resistant slurry pumpDocumentary on high quality development of material industry

　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. WhenKolchin ,　　The water pump is not installed firmly or installed too high.　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.Tao Bo,　　In addition,Kolchin Carbon steel explosion-proof pipeline pump, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, our basic survival is a problem.

　　In this way, when the equipment is used again the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is　　If there is no liquid in the cavity of the self-priming centrifugal pump of the submersible sewage pump, the gas-liquid foam mixture cannot be formed and the air cannot be pumped. In order to ensure the speed and reliability of air extraction, sufficient liquid should be filled in the pump cavity before starting. What time would you like　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump,　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　Reasonable.　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.

　　It is also necessary to clean the ventilation duct to avoid blockage.Discount,　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.　　 WQ series submersible sewage pump has fixed and mobile devices, as shown in the figure. When the fixed driving device is selected,Kolchin Corrosive pipeline pump, the chain cable shall be separately threaded into (away from the pump outlet and its connecting line shall be parallel to the axis of the pump outlet) two lifting eye screws or lifting plates to lift the electric pump up and down,　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,Kolchin ,　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, in the second half of the year there is still a large gap after China&#;s power balance.