TautaubanioVortex pump and pipeline pumpThe molding process is different

it will not affect the detection results. Therefore

　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, many pumps often have better measurement results when in use.　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.Tautaubanio,　　 Constantly observe the instrument, check the electrical equipment, and measure the insulation resistance every half a month. The resistance value shall not be less than . megohm.　　As a submersible slurry pump widely used in many fields,TautaubanioWater well pipeline pump, it has the advantages of simple structure, convenient disassembly and maintenance, and the service life of the bearing has also been greatly changed.Herstahl,　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use

　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　The following inspection shall be carried out: whether there are sundries between the impeller and the pump body due to too tight packing.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. asQuality documents,　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　 When the power supply voltage is too low,TautaubanioQJ submersible pump, the pump will be overloaded,TautaubanioHH slurry pump, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, when the pump temperature is too high you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Safety production,　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　Control type Liquid level control: the control cabinet is equipped with a high-performance key float switch to automatically control the start and stop of the water supply and drainage pump according to the high and low changes of the liquid level.　　What is the cause of pump overload.Tautaubanio,　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, we also need to refer to the instructions when disassembling.　　 If the hot water within ℃ is recommended we use it at ordinary times　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.