stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Manhattan,How to maintain the elevator correctly and replace the hydraulic oil of the elevator regularly: the hydraulic oil used in the elevator is divided into winter and summer. It is not noticed until the hydraulic cylinder of the elevator is working abnormally.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Galle,Conscientiously write the special construction plan for installation and construction, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.It is necessary to check the brake of the guide rail type elevator frequently, and there should be no dirt on the friction surface.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Meticulous workmanshipFeatures of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels,ManhattanGuide rail type lifting cargo elevator, post and telecommunications, municipal gardens, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems,ManhattanHigh performance elevator, etc. The lift has the advantages of light weight, self-propelled electric start, self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.The price is guaranteed, the service is guaranteed and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.
The price is guaranteed the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Quality assurance,Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, and a small rust will appear after a long time. Because most of these scars are small,ManhattanElevating cargo elevator, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Problems to be considered in the transportation of lifting platforms But in the use of elevators, some relatively large places will purchase lifting platforms that suit their needs according to the requirements of users, which means that the equipment that is too large will exist in the transportation Difficulties, this is also a problem that many users and manufacturers are more worried about. The equipment is large in size and occupies a large area. It is inconvenient to carry it back and forth, and it is very difficult to move. So how should we solve it? Today the editor will introduce to you in detail how the large lifting platform solves the problem of transportation difficulties.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Manhattan,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.
