TrutnovStainless steel inner linerShare the early secrets of achieving profitability

Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Application: utility boiler industry, mainly in key parts such as high temperature section of superheater and reheater.Trutnov,Relevant information stainless steel export is an important part of China's export economy. It plays an important role in stimulating China's economic growth. However, China's stainless steel export has encountered great resistance.AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.Mokegua, Series & mdash; martensitic precipitation hardening stainless steel pipe.Stainless steel pipes can be divided into CR series ( Series), Cr Ni series ( Series), Cr Mn Ni series ( Series) and precipitation hardening series ( Series). Series & mdash; Cr Ni Mn austenitic stainless steel series & mdash; Cr Ni austenitic stainless steel.Application: utility boiler industry, mainly in key parts such as high temperature section of superheater and reheater.

Hardness test: annealed stainless steel pipes with inner diameter of more than mm and wall thickness of less than mm can be tested by w-b Vickers hardness tester,TrutnovStainless steel pipe,TrutnovF53 stainless steel plate, which is very fast and simple, and is suitable for rapid and nondestructive qualification test of stainless steel pipes. For stainless steel pipes with inner diameter of more than mm and wall thickness of more than mm, Rockwell hardness tester shall be used to test HRC hardness. Stainless steel pipes For stainless steel pipes with inner diameter greater than mm and wall thickness less than mm, the surface Rockwell hardness tester shall be used to test HRT or hrn hardness. For stainless steel pipes with inner diameter less than mm and greater than mm, the special Rockwell hardness tester for pipes shall be used to test hrt hardness. When the inner diameter of stainless steel pipes is greater than mm, the Rockwell or surface Rockwell hardness tester can also be used to test the hardness of pipes.Selection process of stainless steel pipe water supply pipe.Model & mdash; Add a small amount of sulfur and phosphorus to make it easier to cut.quality index,Stress corrosion cracking (SCC) refers to the cracking caused by the combined action of stress corrosion stress (mainly tensile stress) and corrosion of austenitic stainless steel Austenitic stainless steel is prone to stress corrosion in corrosive media containing chloride ions. When the Ni content reaches % - %, it is a long-term enterprise engaged in stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe. Welcome to consult. The stress corrosion tendency of austenitic stainless steel is very large. Continue to increase the Ni content to ~ %, from the current situation of China's stainless steel foreign trade, China's stainless steel export has encountered great resistance.Using CrO and hsoho as the main components and adding an appropriate amount of mnso.ho coloring solution the chemical coloring of stainless steel industrial pipe was carried out. The effects of pretreatment process, coloring solution temperature, mass concentration and coloring time on the color film of stainless steel industrial pipe were discussed. Through a large number of experiments, a good formula and process range of coloring solution are obtained. With the increase of temperature and time, the film thickness increases, and the color changes are brown, blue, gold, purplish red and green. After curing and sealing treatment, the colored film of stainless steel industrial pipe has more uniform surface color, good reproducibility, and significantly improved wear resistance and corrosion resistance.

Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.Job description,There are various connection modes of stainless steel pipes. The common types of pipe fittings are compression type, compression type, union type, push type, push thread type, socket welding type, union flange connection, welding type and derivative series connection mode combining welding with traditional connection. These connection modes have different application ranges according to their principles, but most of them are easy to install, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber nitrile rubber and EPDM that meet the requirements of national standards. L stainless steel pipe, s stainless steel pipe, L stainless steel pipe and other brand products are provided for a long time. The designated products are complete and the quality is guaranteed which eliminates the need for use　　— The corrosion resistance is the same,TrutnovStainless steel plate, and argon gas is not used inside the weld. The welder's operation is simple and fastTrutnov and the strength is better because the carbon content is relatively high.Flux coated welding wire is used for backing welding,Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment, with low investment cost and good benefit.Low temperature processing of stainless steel pipe --- martensite series stainless steel is quenched from austenitizing temperature and then cooled to very low temperature to promote martensite quenching. It is suitable for stainless steel easy to produce residual austenite.Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).