AklowLifting platform hydraulic pressureWhat industry can be used

Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.Improper use of oil: Inadequate maintenance of high-altitude work platform equipment such as mobile elevators can also lead to small fitting gaps of components, making it difficult for oil to form a uniform oil film on the friction surface. Additionally, due to assembly and other reasons, it is difficult to ensure the uniformity of fitting gaps, thereby reducing efficiency and causing early abnormal wear of equipment components; In severe cases, it may cause scratches or bite on the friction surface of precision fitting,AklowCan hydraulic pressure automatically lift and lower, leading to the occurrence of abnormal equipment noise.Aklow,Readjust the overflow valve when the pressure is low. Adjust the oil level to be too low at % rated load, fill the hydraulic oil with suction oil, filter the blockage and clean the oil suction section of the filter for air leakage. Check the oil suction pipe and joints; Tighten the joint. Replace the connector if necessary.When working in a hot environment, pay attention to heat dissipation.Calumpit,For the safety performance of high-altitude work platforms, it is necessary to have production technology, and strict management to ensure production. When in use,AklowHydraulic lifting platform for loading, people, the environment, and machines are the three major links of high-altitude operations, and safety is the basic condition to ensure the smooth progress of high-altitude operations. In the following text, Jiuyi briefly describes the precautions for using high-altitude operation platforms: high-altitude operators must hold a health certificate. Individuals with mental illness, hypertension, or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.Remove and disassemble the hydraulic lift cargo elevator lowering valve blow out the plunger with compressed air, then install it and reinstall it.It is strictly prohibited to connect the motor of the lifting platform to the wrong power supply. It should be ensured that the voltage is V or V, and daily cleaning work should be carried out. Dust and debris on the motor should be cleaned in a timely manner.

Although lifting cargo elevators have good safety, in practical work, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.Emergency bolts not tightened; The solution is to tighten the emergency valve.Although lifting cargo elevators have good safety, in practical work, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.Professional is king,Signature recognition of.Aluminum alloy elevators, also known as aluminum alloy lifting platforms, currently have a wide variety in the Chinese market. They are highly favored by users due to their flexible movement, light weight, and small size.The inconsistent rotation axis of the support rod in the middle of the hydraulic lifting platform results in the lifting platform being unable to function properly, causing serious damage to the platform and causing the table to tilt. Please carefully check that the general shear type high-altitude work platform was not strictly tested for tilt before leaving the factory, and was put into the market, causing many accidents. For small enterprises, they are not very concerned about this aspect of tilt detection, This is also why there are such a large number of lifting equipment with this problem. The problems with the oil cylinder and power unit system are often due to insufficient power and substandard oil cylinder quality, which are also very important issues for enterprises themselves.

The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.Interpretation and observation,During use, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal, it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found, it must be locked tightly to prevent accidents caused by the shaft pin falling off.Connect the motor naturally to the elevator. When connecting, it is necessary to ensure that the concentricity of the elevator output shaft and the motor input shaft is consistent and the outer flanges of the two are parallel. Inconsistent alignment can lead to motor shaft breakage or elevator gear wear.When encountering overheating in the electric motor during daily maintenance of the elevator, it is necessary to quickly park the car, remove obstacles, and then continue running. The motor bearings should be smooth and excellent.Aklow,Firstly, it is necessary to use and operate the elevator correctly. The operators should receive systematic operation training: regular inspection of operating standards should be carried out and any violations of elevator operation should be detectedFor the safety performance of high-altitude work platforms, it is necessary to have production technology, scientific processes, and strict management to ensure production. When in use, people, the environment, and machines are the three major links of high-altitude operations, and safety is the basic condition to ensure the smooth progress of high-altitude operations. In the following text, Jiuyi briefly describes the precautions for using high-altitude operation platforms: high-altitude operators must hold a health certificate. Individuals with mental illness,AklowMobile hydraulic lifting platform/lifting platform, hypertension, or mental illness are not allowed to engage in high-altitude work tasks. Staff are not allowed to engage in high-altitude work while drinking alcohol or feeling mentally drained.The inconsistent rotation axis of the support rod in the middle of the hydraulic lifting platform results in the lifting platform being unable to function properly, causing serious damage to the platform and causing the table to tilt. Please carefully check that the general shear type high-altitude work platform was not strictly tested for tilt before leaving the factory, and was put into the market, they are not very concerned about this aspect of tilt detection, which are also very important issues for enterprises themselves.