Slavonia brothers12Cr2MoWVTiB alloy pipeChange driven share

What should we pay attention to in the production of alloy pipeThe delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Slavonia brothers Pipe installation:It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact, this cognition is wrong. H-beam and I-beam are different in shape!Tamiyah,As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market the structure of the I-beam has determined its torsional performance. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Defects of alloy pipe and solutions:

→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.Blanking shall be carried out according to the design and site, and then the groove shall be made with a grinder with a groove angle of ° ~ °. Fix the processed pipe on the support, and the gap between the two pipes is mm ~ mm, and then weld.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.Direct labor, H steel has its own advantages and disadvantages.Key technical characteristics of alloy pipe:The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

Determined by the shape, the section modulus,Slavonia brothersGH2132 superalloy tube, moment of inertia and corresponding strength of I-beam are obviously better than those of ordinary I-beam with the same single weight. When used in metal structures with different requirements, pressure load and eccentric load. Compared with ordinary I-beam, it can greatly improve the bearing capacity and save metal by % ~ %.details,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.Galvanized pipe refers to the shape and high frequency of hollow square steel pipe welded by the back of the steel pipe during the hot rolling or cold rolling of galvanized steel plate or cold bending of galvanized steel plate, or before the galvanization of cold hollow pipe. Galvanized. Galvanized square pipe can be divided into hot galvanized pipe and cold galvanized pipe from the production process. This is because the two galvanized pipes are different which also leads to many different physical and chemical properties.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Slavonia brothers, H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Requirements of alloy tubes for low and medium pressure boilersI-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide,Slavonia brothers16Mn large diameter seamless pipe, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.