GuangyangTwo layers of hydraulic lifting cargo elevatorNormalizing

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Guangyang,The 'streamlined' open loose-leaf joint design of the hydraulic boarding bridge increases the welding area by more than times compared with the general tubular joint, which effectively prolongs the service life and simplifies maintenance.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that remove the motor shaft key.Buhusi,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.The price is guaranteed the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.

Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, and once found, go to a professional beauty shop for processing.How to solve the leakage of the oil pipe when the elevator sinks? It may be that the seal is damaged, or the oil pipe has cracks, which leads to a drop in pressure and cannot support it to a large height.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production,GuangyangSmall cargo elevator,GuangyangHydraulic lifting cargo elevator, a special lifting device is required to be fixed at a certain position of the production line.Quality Assurance,Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Executive standard,The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Advantages of operating cost: Low failure rate, the failure rate of elevator operation can be reduced to a minimum. Less power consumption: When the hydraulic elevator goes down, it is driven by the pressure generated by its own weight, which greatly saves energy.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Guangyang,Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle,GuangyangSimple cargo elevator lifting cargo elevator, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.