MazetourWarehouse elevatorProduction process

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Mazetour,As long as we transport the lifting platformTake the measures that need to be taken during the transportation of the lifting platform in advance to prevent all possible problems, and then the difficulties will be solved. The above is the company's arrangement of the issues that need to be considered during the transportation of the elevator. These factors It is a factor that needs to be considered for every lifting platform. Therefore, we must try our best to be perfect and impeccable. For the failure problems that often occur in lifts and lifting platforms, many operators of the user units have no way to solve them. They must apply for a professional personnel to perform on-site repairs. However, due to the obstacles of the working environment and time factors of the equipment, the failures of the equipment cannot be fully repaired normally, and only some special measures can be taken to maintain the basic working performance of the equipment.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Tamale,Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Hydraulic pump station: special pump station for domestic lifting platform protection device outside the pump station imported from Italy: organ m type, iron plate seal type.

The contact opening and closing of the travel switch of each safety device must be reliable mesh type, it is necessary to use and operate the elevator correctly, and provide systematic operation training for the operators: regular inspections of the operation specifications are required, and if any violation of the regulations is found, and those who are serious must be transferred from the post. Through the elevator production experience since the company, it is found that most elevator customers have overloaded elevators. Although the elevator has a large overload in design, the hidden dangers brought about by such use are very large, and it is easy to cause the oil cylinder to fall. , lift bracket deformation and other injuries. Therefore, there must be the following summary: the maintenance of the elevator must be equipped with full-time elevator operators who have undergone on-the-job training, and illegal operations are strictly prohibited.The daily maintenance of the hydraulic lifting platform in normal use is essential,MazetourChain guide rail type cargo elevator, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.production,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected,Mazetour20 ton lifting cargo elevator, single-phase or three-phase power supply and diesel engine.

Are the water cooling and air cooling of the hydraulic station the same?Sales Department,The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Any kind of machine or equipment will go through a series of inspections and adjustments before leaving the factory until all links are qualified. Take the mobile lift as an example, the same is true. Of course, there will still be some problems with the lift during practical use, but there is no connection, as long as you master some specifics, you can effectively solve these problems.After the goods are transported, clean up the debris on the platform.Mazetour,What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, it must be washed off with gasoline or thinner.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground,MazetourIndustrial cargo elevators, does not occupy the ground space, and does not affect the passageway.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.