Gu YeHydraulic fixed lifting platformPre-sale plan process

The elevator adopts high-strength and high-quality materials, which have the advantages of beautiful appearance, small volume, light weight, stable lifting, safety and reliability. Its appearance allows for high lifting capacity in extremely small spaces. The column lifting system has the characteristics of large load capacity, strong stability, and convenient implementation. There are many applications for mobile elevators, so we must enhance the safety awareness of using aluminum alloy elevators. Below, let me tell you some precautions.The elevator has strong controllability, simple operation, and high accuracy, which can meet different needs of different heights, press and stop, making high-altitude operations simple and feasible.Gu Ye,When in use, the four legs of the elevator must be supported because the four tires are not under force, so the lower frame of the four-wheel elevator must be horizontal.Secondly,Gu YeJiangsu hydraulic lifting platform, frequent voltage instability can directly burn out the power unit motor. The consequences of motor burning are very serious, which can lead to an instant decrease in pressure. If the equipment is not equipped with safety devices such as relief valves or explosion-proof valves, it can cause the lifting equipment to fall, leading to accidents. At the same time, its weight is borne by the four parts of the elevator. Over time, the tires of the elevator may deform due to excessive pressure. So when we are idle, we must open its four support legs to bear the weight of the elevator itself, in order to protect the rubber tires.The elevator has strong controllability, simple operation, and high accuracy, which can meet different needs of different heights, that is, press and stop, making high-altitude operations simple and feasible.Drain and discard the hydraulic oil, tighten the joint, remove the oil filter, clean it with compressed air, and then return it to the oil tank and connect the pipeline.

The vehicle body should be grounded according to regulations, and the lifting operation should be commanded by the person in charge of the work. The person in charge should follow the standard signal and communicate with the lift operator. The signal emitted must be clear and accurate.Check for wear on rollers, intermediate shafts and bearings, oil cylinder pin shafts and bearings, boom hinge shafts and bearings, etc.A type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve throttle valve, and balance valve hydraulic control one-way valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.Inspection items, it is necessary to raise and lower the elevator several times at regular intervals to ensure that the hydraulic oil inside and the grease on the components are not misaligned due to prolonged immobility. It is also important to pay attention to the operation of the components to be observed. If the temperature is relatively low it is necessary to frequently check the hydraulic oil of the elevator. If it is abnormal, it should be replaced with new hydraulic oil in a timely manner. Mechanical maintenance should also be done well, otherwise oxidation and deterioration may occur and cause damage to the elevator. Specializing in product and renewable resource business, including mobile elevator manufacturersWe are well aware of the harm of pressure, but how can we prevent water from seeping into the hydraulic system of the elevator? After reading this article, you may know that oil contains excessive water impurities, which can rust the hydraulic components of the elevator, emulsify and deteriorate the oil, reduce the strength of the oil film and accelerate mechanical wear. In addition to preventing water impurities from invading during maintenance, it is also important to note that when the oil storage tank is not in use, and the hydraulic oil of the elevator that is filtered each time needs to be replaced with a dry filter paper. In the absence of specialized instruments for detection, the oil can be dropped onto the hot iron plate, and no steam can be emitted before being added immediately. So when repairing the hydraulic system of aluminum alloy, be careful of the entry of moisture!

The elevator has strong controllability, simple operation, and high accuracy, which can meet different needs of different heights, that is, press and stop, making high-altitude operations simple and feasible.consumption,The lifting drive chain is a double chain structure using industrial plate chains with high bearing capacity and safety factor.Electric elevators are currently commonly used lifting equipment in industry, mainly used for high-altitude operations and the transportation of goods at different levels. Electric elevators are easy to operate, have good performance, and have a wide range of operations, widely used in various industries such as chemical, municipal, and power. Electric elevators are divided into various types, including scissor fork type, sleeve cylinder type, single column type, etc. One of the most commonly used ones is electric elevators.A specially designed guide wheel device between masts ensures smooth and smooth lifting.Gu Ye,To reduce noise, increase the clearance inside the platform, and also make the transmission more stable and the mechanism vibration less.What are the standards for selecting manufacturers of elevators? After confirming the model, configuration and manufacturer, you can basically understand how much the user wants for a lift.Elevator: The fully automatic high-altitude work platform has a sturdy structure, which minimizes the deflection of the high-altitude work platform. Equipped with automatic walking function, it can walk in different working states without the need for external power supply. The handle can walk at an adjustable speed, with flexible movement, convenient operation, and easy lifting. Only one person can complete forward, backward, turning, fast, slow walking, and up and down movements, saving labor and effort. Can be designed and produced according to user requirements.