SirutIrrigation deep well pumpHow to solve the sinking problem

　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurrySirut,　　 Pipeline booster pump: in fact the pipeline booster pump is what we often call a booster pump. It is named according to the purpose of the pump. As the name suggests, any pump that can pressurize the liquid delivered in the pipeline can be called a pipeline booster pump. Not limited to one type of pump, such as centrifugal pump, pipeline　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mmLa Libertad,　　Superior,SirutZD slurry pump,SirutSewage pump diving, complete protection s, reasonable structure convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, the motor shaft drives the water pump impeller to rotate, and transmits energy to the slurry medium to generate a certain flow rate, and realize the transportation of slurry.　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously, and the gate valve or flap valve is not closed tightly.

　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　 The main circuit water pump control cabinet is mainly composed of isolation circuit, short-circuit protection, overload (backup) protection circuit, start / stop (variable speed) control appliance, thermal relay and distribution wire and cable forming the protection for the water pump motor. Set various monitoring signals as required.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use,　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise,SirutSelf priming slurry pump wholesale, if the flow is too small,Open the gate valve.　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.

　　Submersible pump is a common water lifting equipment for deep wells. During operation, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersibletarget,　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　Its working principle is as follows: when the screw pump is working, the liquid follows the sealing cavity to move along the axial direction from the suction side to the discharge side of the pump, and the continuous suction and discharge realize the liquid transmission .　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impellerSirut,　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　Reasonable.　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can