Las VegasAh slurry pumpComprehensive maintenance support

　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,　　It is not correct that it has no effect on us.Las Vegas,　　 Constantly observe the instrument,Las VegasISG single stage vertical pipeline pump, check the electrical equipment, and measure the insulation resistance every half a month. The resistance value shall not be less than . megohm.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.Tashkurgan,　　Work, no noise and vibration,Las VegasIrrigation deep well pump, and the site is cleaner.　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　When using the sand pump, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid

　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled,Las VegasQuotation slurry pump, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　 during operation, the deep well pump shall rotate smoothly without vibration and abnormal sound. Observe whether there is obvious fluctuation in the motor running current and line voltage before and after startup. The change of water level in the well shall be observed frequently. The motor must not be exposed to the water surface or sink into the sludge to avoid affecting the power supply　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowsDesign brand,　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more

　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?Create brilliance,　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　Actually, you don&#;t have to worry about this. First of all, stainless steel has very strong anti-corrosion ability compared with products that are easy to rust. When many friends buy stainless steel deep well pumps, their manufacturers will apply a thin anti-corrosion coating on the outer layer of the equipment according to the needs of consumers. as　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact it is mainlyLas Vegas,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　Ordinary vertical motor can be used without waterproof while the motor shaft and pump shaft of submersible slurry pump are coaxial, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　 If the power cord is not well contacted, it will also lead to the burning of the motor.