Stabia CastleHydraulic electric lifting platformWiring construction process

. The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. In order to ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve and balance circuit are installed on the return oil circuit to maintain pressure and ensure that the descent speed is not affected by changes in heavy objects. The throttle valve regulates the flow rate and the lifting speed. To ensure safe and reliable braking and prevent accidents, a hydraulic one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking when the hydraulic pipeline bursts. Install an overload sound alarm to distinguish between overload or equipment failure.Emergency descent device: When a power driven chain elevator loses power,On the other hand, under the action of high pressure the hydraulic system inevitably causes the hydraulic valve to flow back or the sealing components to produce oil. The main reasons for the natural descent of the hydraulic cargo elevator include the following points: replacement of the support valve due to leakage. The lowering valve is damaged or not powered on. Require the lowering valve to be kept clean on a daily basis, and if damaged, replace it with a new hydraulic lowering valve in a timely manner.When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level , please stop using it; When the lifting height exceeds meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed,Next, the hydraulic cargo elevator manufacturer will explain the maintenance of the mechanical equipment of the elevator: the brakes of each organization should be frequently checked and adjusted to ensure the clearance between the brake pads and wheels is sensitive and reliable. On the surface, there should be no dirt present. If there is dirt, it is necessary to wash it off with gasoline or thinner.Each box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.

When the hydraulic system malfunctions,Stabia CastleElectric lifting platform Hydraulic lifting platform, the hydraulic elevator may experience problems with the hydraulic pump, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.In addition, the convenience of the layout is also a very important issue. For example, in areas with large or high waves, there may be layout issues when using a lifting mechanism. At this point in order to facilitate the arrangement and prevent the hydraulic cargo elevator cylinder from being eroded by waves, a lifting structure should be selected to determine the installation position of the oil shoulder, as the lifting point of the bridge is not in a straight line during the lifting process. Therefore, during the lifting process of the cylinder, the connection between the two ends of the cylinder and other components must be hinged in the same square. In addition the installation of the hydraulic cargo elevator cylinder must also be determined through comparison and calculation, whether it is the tail lifting ear type, the middle pin shaft type, or the head pin shaft type. The main advantage is that the effective area of the cylinder is large, and the overall installation height is low. The disadvantage is that if the cylinder stroke is large, there may be stability issues with the cylinder, and the cylinder layout may be difficult. The main advantage of the hydraulic cargo elevator lifting mechanism is that it does not have a stable transmission installation frame for height measurement. Therefore, this form can be considered in places with large drops. The sudden deafness oil type on the head can reduce the installation height, but if it is too large, the oil cylinder will experience an increase in force due to the lifting height. Moreover, the higher the lifting height, the faster the increase in force, which is not suitable for the use of the oil cylinder. Therefore, when it is too large, the head pin type is not suitable. In order to comprehensively consider the height of the installation bracket and the force on the oil cylinder during the lifting process, an intermediate installation method can be considered, and the installation position can be set at an appropriate height according to calculations.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.Where can I find it?, also known as hydraulic powered elevators.Load bearing capacity: The lifting platform is placed on a horizontal support surface which has been favored by a large number of enterprises and individual customers. Hydraulic elevator is a multifunctional heavy loading and unloading mechanical equipment. The lifting system of hydraulic elevators is driven by hydraulic pressure, and the workbench is evenly loaded to % of the maximum load capacity. After lifting times, each load-bearing component must not have deformation or cracks.Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.

After long-term use of the automatic lifting platform equipment,Stabia CastleCylinder mounted hydraulic lifting platform, it is inevitable that some malfunctions will occur. In order not to affect work,Stabia CastleImported hydraulic lifting platform, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.system,The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.It is prohibited to work on unstable structures (such as asbestos tile roofs). To prevent accidental boarding, warning signs should be hung at necessary locations of this structure.Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.Stabia Castle,Each box, distribution box, and the depth should not exceed .mm.The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.