RaleighElectric hydraulic fixed lifting platformWhat is the post-maintenance method

If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.When using hydraulic elevators, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).Raleigh,Hydraulic elevators and load-bearing oil cylinders can directly act on the foundation pit, requiring low shaft strength, and brick or brick concrete structure shafts.Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.Thessalonika,Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.An inverter can also generate high noise. When the power supply voltage is lower than % of the rated voltage the short circuit ring of the iron core of the device breaks, dust or rust is poor, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.Cleaning and maintenance: When there is oil in the oil tank or when oil is refilled, it is necessary to ensure the cleanliness of the filter tank cover. Clean the oil and funnel or container before use. Never bring dirty things into the system, only clean oil.Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.Installation works,When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than %. The meshing gap should be appropriate.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen,RaleighManual hydraulic lifting platform, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.The characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity,RaleighHydraulic lifting platform, and rear hinge support.

After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally due to overload, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.Affordable price,Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However,RaleighFixed hydraulic lifting platform, there are still certain limitations, such as height and improving the quality of goods, which have certain constraints.All high-altitude operations must first build scaffolding or take measures to prevent teams from falling before boarding the vehicle bridge.Next, the hydraulic cargo elevator manufacturer will explain the maintenance of the mechanical equipment of the elevator: the brakes of each organization should be frequently checked and adjusted to ensure the clearance between the brake pads and wheels is sensitive and reliable. On the surface, there should be no dirt present. If there is dirt, it is necessary to wash it off with gasoline or thinner.RaleighWhen the hydraulic oil of the equipment is insufficient, you only need to add enough hydraulic oil to run.After hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms.