AshdodLong shaft submerged slurry pumpInspection process analysis of

　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, increase production and ensure income, and provide material conditions for agricultural mechanization and water conservancy.Ashdod,　　For /g-g gravel pump, which belongs to large-diameter slurry pump, it is necessary to remove the impeller removal ring and rotate the impeller in the opposite direction.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageUherske Hradiste,　　Some of them are OK. For irrigation and other purposes, in fact,AshdodFire deep well pump, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.

　　Commodity.　　Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire.　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energyGood quality,　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water mine rescue, industrial cooling, farmland irrigation, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look today　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency,AshdodCentrifugal slurry pump, the water pump will automatically start to supplement the pipe network pressure.

　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleLet's see,　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　Eliminate hidden dangers of fire pump in time.　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life,AshdodWQ submersible pump parameters, protection should be done well, which should be a comprehensive optimization design method.Ashdod,　　 When stopping the operation of the submersible slurry pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump etc. are all in the application scope of the slurry pump