AtaimSubmersible slurry pumpClick to view

　　Submersible slurry pump can be widely used in mining, power metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, river dredging, etc. In chemical industry　　Water pump After understanding the cause of insufficient liquid supply, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Ataim, the pipeline booster pump is what we often call a booster pump. It is named according to the purpose of the pump. As the name suggests any pump that can pressurize the liquid delivered in the pipeline can be called a pipeline booster pump. Not limited to one type of pump, such as centrifugal pump pipeline　　Commodity.Gueines,　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　 Another possibility is that the gas is sucked in when the pump is in use.　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravity

　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.　　The actual operating flow is too large, resulting in the following results: when the flow increases, the shaft power of the pump increases, while the efficiency of the motor remains unchanged so the power of the input motor must increase. Excessive power makes the motor in an overloaded operation state, which may cause heating or even burn out the motor　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleRecommendation and consultation, it will not affect the detection results. Therefore,AtaimAh slurry pump, many pumps tend to have better measurement results when in use.　　 When adding lubricating oil to the pump at ordinary times,AtaimWQ submersible sewage pump, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.

　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, V-shaped irons of the same specification,AtaimWQ submersible pump parameters, clean kerosene, oil basin, cotton yarn, etc.Welcome to inquire,　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press the　　The quality of the substitutes produced is not up to the standard, and the price of imported spare parts is expensive; Moreover, in the subsequent sludge treatment unit, the flow passage parts of the centrifugal dehydrator are more sensitive to sand particles. Therefore, sand particles in the conveying medium shall be minimized.　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.Ataim,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.