Chatham KentISG single stage vertical pipeline pumpSales methods

　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment,Chatham KentBaigang deep well pump, landscape fountains, etc. Submersible pump is generally divided into clean water submersibleChatham Kent,　　 No leakage protector is installed: leakage protector is also known as lifesaver. If the leakage value of the submersible sewage pump is higher than the working current value of the leakage preventer, the leakage preventer will cut off the power supply of the submersible pump to ensure the normal operation of the equipment.　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.Ech Chettia,　　If there is a standby pump, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water,Chatham KentWater well pipeline pump, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry

　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　It is worth noting that the QW mobile type is generally used without a fixed position, so it is usually used temporarily without an electric control cabinet, and a special person is required to control the shutdown of the water pump.　　The two have certain commonalities. They are both submersible. As the name suggests, but generally speaking people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumpingInterpretation and observation,Chatham KentDeep well pump,　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.

　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.Total quality assurance,　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　 Temperature control: an external temperature controller is used to turn on or off the pump according to the set temperature range. It is used in constant temperature, heat exchange system and other occasions requiring temperature control.　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pumpChatham Kent,　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　Only in this way can its service life be extended to a large extent.　　 The fan speed of the water pump is too low, so the heat cannot be dissipated.