SalmiaAh slurry pumpHighlight professional standards

　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowsSalmia,　　Water pump control cabinet Time control: the chassis panel is equipped with a time setting button and a display. The user can control the opening and closing of the water pump according to the timing needs. It is suitable for the control of various timed or regular intermittent working modes.　　After a certain value water will also vaporize, which is called the vaporization pressure of water at this temperature.Connecting again,　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump

　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　What faults will the water pump control cabinet often encounter in use? The water pump cannot work: cause: a. the power supply is not connected or the output phase of the control cabinet is missing; b. The water pump has been burnt out, and the water pump can not supply water: cause: A. whether there is water in the pool; b. Whether there is gas in the pump body that is not discharged; c. Inlet and outlet water　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.Fair price,　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in water　　As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, especially meeting the needs of deep-water sand pumping and dredging. At present,SalmiaRubber lining submerged slurry pump, the depth can reach meters.　　Troubleshooting: first increase the water pressure then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.

　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pumpassets,　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　Shaft seal water, no dilution of pulp,SalmiaQuotation slurry pump, good shaft seal effect. It can be used when the slurry is not allowed to be diluted.　　Then it can enter into the volute pump housing. Then in the volute pump casing,SalmiaTwo stage slurry pump,　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　 First remove the pump from the engine.　　Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because