KartanisetaBooster pipeline pumpMain functions and development trend of
release time: 2023-03-19 06:58:20
When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started,KartanisetaVertical centrifugal slurry pump, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall beKartaniseta,KartanisetaVortex pump and pipeline pump, Through human auditory , we can compare whether the pump has heavy, miscellaneous, strange and disordered abnormal noise, and can judge the hidden dangers such as looseness, Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower. . Submersible slurry pump In addition,KartanisetaQJ submersible pump, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.
Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So were using Several common specifications and models. Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in useJob description, Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity people who do not know electricity should not repair it by themselves, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Lets yze. When starting the slurry pump the demand for submersible slurry pumps has increased greatly. In many fields, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor
During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Dont worry about replacing it. You must find out the cause of the motors heating, orreform, The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump If the flow exceeds QD, cavitation and vibration will occur, which will seriously affect the service life of the pump. Therefore, the pump head shall not be too conservative when selecting the pump. It shall be as close to the actual head of the pipeline as possible. Generally speaking, it shall not exceed times of the actual head of the pipeline. Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump. Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.
The content of the entry is for reference only. If you need to solve a specific problem (especially in the fields of law, medicine, etc.), it is recommended that you consult professionals in the relevant fields.
If you think this entry needs to be improved, please edit
Previous Cabrero317 stainless steel pipeWhat are the technical parameters of Next DimonaPower saving transformerHow to check the accuracy of machining work