KinaSubmersible sewage pumpWhere can we see the current status

　　 It may be that the motor power of the water pump is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersibleKina,　　Static water level refers to the water level before the pump is started.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump so we should follow the correct steps to connect.Luanshya,　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant,KinaDeep well pump, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings,KinaSplit vertical pipeline pump, so when the situation is relatively minor, the motor is only in local places　　; When the electric pump has sudden noise or large vibration; When the protection switch frequency trips.　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.Installation conditions,　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main　　It is located in the middle, so it seems that many regions have good effects when using it.　　For example, in the market, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.

　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the waterindex,　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　 Pipeline booster pump: in fact, the pipeline booster pump is what we often call a booster pump. It is named according to the purpose of the pump. As the name suggests, any pump that can pressurize the liquid delivered in the pipeline can be called a pipeline booster pump. Not limited to one type of pump, pipeline　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.Kina,　　When the water level reaches,KinaUsed pipeline pump, the frequency of the frequency converter drops and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, the noise method directly detects the noise of the equipment in the detection process, so in fact, such measurement is not very accurate.