SisimbraCarbon steel explosion-proof pipeline pumpTechnology and promotion of accelerating capacity removal

　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.Sisimbra,　　The treatment methods are as follows: Check the power supply voltage: if the voltage changes greatly, it is caused by unstable voltage, and the use should be stopped immediately to prevent more serious consequences. Or install corresponding heat dissipation protection measures to protect the motor.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without itsLas Rozas de Madrid,　　With the continuous development of slurry pump technology submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe,SisimbraUsed pipeline pump, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,

　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft and successively install the bearing inner race, bearing gland and retaining sleeve　　In addition to conventional accessories, ordinary long shaft pumps can also manufacture deep well pumps with different al characteristics according to the special requirements of customers. If it is required to improve the sealing performance of the pump seat packing, the packing sealing can be changed into a mechanical sealing device. If there is backpressure water at the wellhead, a sealed pump seat can be used. If required in none　　The premise of using this method is that the water gun must have sufficient flow during use,　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.

　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!project,SisimbraSmall deep well pump,　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency the water pump will automatically start to supplement the pipe network pressure.　　If there is no liquid in the cavity of the self-priming centrifugal pump of the submersible sewage pump, sufficient liquid should be filled in the pump cavity before starting. What time would you like　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.Sisimbra,　　The direction of the differential pressure force is opposite,SisimbraWQ submersible sewage pump, which can offset part of the axial force and prolong the service life of the bearing.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.