AachenGrouting small conduit and advance anchor rodPrecautions for

The commonly used standard for grouting pipe is the inner diameter of -mm. The wall thickness of the pipe has little effect on the sound transmission, so there is generally no need to restrict the thickness of the pipe wall. However, from the perspective of saving steel consumption, it is OK if the pipe wall can bear the lateral pressure of new concrete, lateral and angular directions on the pipeline. From the perspective of its performance, the internal pressure grouting pipe can be displaced in three directions, but because it is limited by casing and other accessories, it can often only be displaced in the axial direction. Therefore, the user needs to indicate the displacement in several directions when selecting and ordering, so as to select correctly. The working principle of the grouting pipe is to use its own elastic deformation to compensate the axial, angular, lateral and combined displacement of the pipe due to thermal deformation, mechanical deformation and various mechanical vibrations. The compensation has the s of sealing, pressure resistance, temperature resistance, corrosion resistance, impact resistance, vibration reduction and noise reduction, which can reduce the deformation of the pipe and improve the service life of the pipe.Aachen,[] Middle label: refers to flange, refers to fixed cutting device, refers to tightening blade device, refers to tightening blade nut, refers to cutting rotating device, refers to cutting blade, refers to pulley and refers to bearing. It has good flexibility. The pipes can be coiled when they are produced so that the number of joints in the pipe network can be reduced. It can be laid according to the terrain, easily bypass obstacles,AachenLeading small conduit manufacturer, does not require preparations outside the construction site, is convenient and fast ( times faster than the traditional welding method) is simple to fix the grouting pipe to the reinforcement cage, and is not affected by the bad weather.Can the stretching speed of grouting pipe be defined?The important reason for the stability of the grouting pipe reinforced soil subgrade is to further verify the main principle of the grouting pipe reinforced soil subgrade treatment technology. It is to place various types of grouting pipe products inside, on the surface of the soil mass or between the layers of soil mass. Relying on the tensile characteristics of the grouting pipe, the distribution of the internal stress field and displacement field of the reinforced soil mass is changed through the friction and embedment between the grouting pipe and the surrounding soil mass.

When the grouting pipe is installed, the axis deviation shall be ≤ cm, and the bearing capacity of the support joint shall meet the design requirements. When connecting the grouting pipes, bolts must be installed symmetrically and tightened in sequence. Meanwhile, in order to prevent excessive deflection of the grouting pipes when axial force is applied, the deflection must be corrected to the horizontal before axial force is applied.Polymer chemical grouting method is applicable to reinforcement of sandy soil foundation, curtain grouting of dam foundation, water stop and leakage stoppage of underground engineering, reinforcement of muddy interlayer of dam foundation and fault fracture zone. There are many varieties of polymer chemical pulp materials, including epoxy resin acrylamide (propionate), polyurethane (cyanogen), lignin, etc. Acrylamide and polyurethane are commonly used in chemical grouting of foundation. Acrylamide pulp is composed of main agent acrylamide and various admixtures. The viscosity of the slurry is close to water, and it has good groutability. After the slurry solidifies, the gel is impermeable, and has good durability and stability. This kind of slurry is widely used in seepage prevention grouting of fine rock cracks and medium fine sand layers and dynamic water leakage stoppage projects. This kind of pulp has certain toxicity and pollutes air and groundwater. The polyurethane slurry is mainly composed of polyisocyanate and polyether resin, and then mixed with various admixtures. After the slurry is poured into the formation, it reacts with water to form polyurethane foam, which can strengthen the foundation and prevent seepage and leakage. Polyurethane slurry can be divided into water-soluble and non-water-soluble. The water-soluble polyurethane can be miscible with water and react with water to form an aqueous gel; Water insoluble polyurethane can only be miscible with organic solvents. Polyurethane slurry has low viscosity, good groutability, high stone strength, safety and reliability, no pollution to the environment, simple operation and high economic benefits. The bottom of the horseshoe of the grouting pipe is too low. After the horseshoe is seated in the mold, the space between the outer mold and the horseshoe surface is greater than the thickness of the pipe wall.how much,Several common failures in the installation of grouting pipes always have many problems when using grouting pipes for work. In order to enable everyone to provide production to the factory normally, we have specially summarized the following failures that will occur when using grouting pipes. If you have problems in the following examples, you will know how to solve them The first point is that if the joint, nozzle or bottom of the grouting pipe is not tightly sealed, it will be blocked by cement slurry during construction. At this time, it is OK to check the sealing The second point is that the joint is misaligned or deformed during installation. At this time, we need to know that it is caused by the thin material selected. The above two points are common problems in the installation of grouting pipes that are not suitable for the current location. We&#;d better remember these points of attention, so that when they occur in the future, we will know how to deal with them to ensure a quick solution! The grouting pipe joint or the pipe orifice and the pipe bottom are not sealed tightly, so please bring in mud or cement slurry during the construction process to block the pipe: during the installation and grouting of the grouting pipe, the rebar is distorted or collided, causing the dislocation and deformation of the grouting pipe joint or the deformation of the pipe wall. The main reason for this is the selection of thin-walled grouting pipes.Among the many imported projects, the development of the production technology of automobile door and window sealing strips is the most representative. Through the introduction of sealing strip production lines from Japan, Germany, Italy, Britain and other countries, up to now, domestic manufacturers have introduced more than sealing strip production lines. In addition to pure rubber sealing strips, sealing strips of various composite structures, metal skeleton and various rubber composite sealing strips rubber and plastic composite sealing strips can be produced. At present, the overall level of China&#;s sealing strip production technology has basically reached the level of foreign countries in the s, and has become a grouting pipe. Because some projects are not easy to detect when they are manufactured, and the quality of the grouting pipe as a channel for testing instruments has become crucial. If the quality of the grouting pipe is poor, it will bring many hidden dangers. Steel grouting pipe material, which has the characteristics of thin pipe wall, steel saving,AachenPipe shed and small conduit, impermeability,AachenSupport small conduit, is generally used for post tensioned reserved holes in prestressed structures. When the grouting pipe is used, it can be directly bound to the reinforcement framework. Because the grouting pipe is very light it is very convenient to operate. However, attention should be paid to the balance of its axis during installation. Action mechanism of grouting pipe: the grouting pipe is a flexible material. Under the action of soil load, high-strength alkali free glass fiber through a certain warp knitting process, and fiber filament coated on both sides.Good reputation,In the construction of some grouting pipes, after the completion of the construction of the project, because some construction personnel did not take protective measures after the completion of the grouting pipes, the project was damaged due to some external factors. In order to help users effectively improve the construction quality of the grouting pipes, the following article introduces the protective measures that should be taken after the completion of the construction of the waterproof layer of the grouting pipes. For various engineering designs, waterproof and water stop shall be carried out throughout the whole process of grouting pipe until the backfilling soil is completed.In fact, this . is the result of the Pi of times the density of and then divided by . If you don&#;t bother, the formula can also be written into the following form to calculate the weight per linear meter: weight per linear meter = (diameter - wall thickness) * * wall thickness / * Disposal method: the grouting pipe shall be shortened according to the specification.Aachen,Before the installation of the grouting pipe, it is necessary to check whether the processed support is vertical to the grouting pipe fitting, and correct the non vertical support; Then install the grouting pipe on the bracket and fasten it.How to deal with the joint if the grouting pipe is installed in sections? If the grouting pipe is installed in sections, the joints must be welded. The welded joints of the section steel have been prepared in the manufacturing plant, and can be installed after the two-phase adjacent joints are aligned. After all beams are welded, anchor them according to the above steps. Install the formwork at the beam end. The formwork shall be made according to the overall dimensions of Hainan grouting pipe device and the notch of the reserved slot. The formwork shall be made quite tight to prevent mortar from flowing into the displacement control box or into the beam end gap.After checking that the installed formwork is tight and seamless clean the reserved groove, then pour concrete and vibrate it tightly. The concrete shall have at least the same strength as the structural concrete at this place, and the grouting pipe device in Hainan shall be kept clean when pouring concrete. It is applicable to the laying of buried pipes in gas pipeline projects, and is not applicable to the use of open pipes. The service life of pipes will be affected by the perennial ultraviolet corrosion of sunlight. How to use the grouting pipe after rusting will not affect its . The grouting pipe is a kind of rubber plate we often see. It is widely used and has a long service life. It has been praised and recognized by people. Next, I will introduce the relevant knowledge of the grouting pipe we produce in detail!