Neratovic12Cr1MoVG thick wall seamless pipeWhat are the outstanding problems in the industry

The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Requirements of alloy tubes for low and medium pressure boilersNeratovic,Galvanized pipe features:It can withstand continuous moderate impact and can provide composite plates of various thicknessesSi Sa Ket,I-beam has wide flange thin web,NeratovicHow much is a 25mm galvanized pipe, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.The alloy tube can be hardened by induction heating, so it has excellent rolling fatigue characteristics and corrosion resistance. Therefore, this kind of steel has been widely used as the material of rolling mill flap ball screw in rolling mill manufacturers. In addition to the excellent properties of cronidur steel, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, and its application range is expected to be further expanded.

When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams.The advantages of shiny galvanized pipe are:It is widely used in various fields of national economic construction, such as buildings, bridges, power stations, oil drilling platforms, vehicles, highways, subways, steel structure plants and large warehousesequipment maintenance ,The pickling agent in the pickling process contains many acidic substances, sodium cyanide, which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.

Under the action of thermal stress because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling,NeratovicHow much is 30 I-beam per meter, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, material composition and heat treatment process. The faster the cooling rate, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate,Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified, such stainless steel plate can be applied.Metric welded pipe: it is used as seamless pipe in standard. The welded steel pipe expressed by outer diameter * wall thickness mm is welded by hot and cold strip welding of general carbon steel, high-quality carbon steel or Puneng low alloy steel, or it is made by cold drawing after hot strip welding. Metric welded pipe is generally used as structural parts, such as transmission shaft, or to transport fluid. The thin wall is used to produce furniture and lamps. It is necessary to ensure the strength and zigzag test of steel pipe.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Neratovic,Introduction to product knowledge of alloy pipe: Small longitudinal crackDetermined by the shape, the section modulus, moment of inertia and corresponding strength of I-beam are obviously better than those of ordinary I-beam with the same single weight. When used in metal structures with different requirements, it shows its superior performance in bearing bending moment, pressure load and eccentric load. Compared with ordinary I-beam it can greatly improve the bearing capacity and save metal by % ~ %.