KadanWhat are the manufacturers of high frequency welded pipeProduct development trends and emerging categories

H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam. Peak crackKadan,Galvanized pipe is often seen in our daily life, especially in some construction sites. This product has the advantage of durability when used. It also has the characteristics of surface gloss, uniform zinc layer and no missing plating. Moreover, the cost of hot-dip galvanizing for rust prevention is lower than that of other paint coatings. In addition, this product also has the characteristics of no dripping,KadanGh2747 superalloy tube, strong adhesion, breaking the clean Legion and strong corrosion resistance. Even if it is used in some places where the environment is not good, its service life is also very long, in urban or offshore areas, standard urban or offshore areas can be maintained for years without repair. The products produced by our company must meet these requirements. Friends who need to order can call us directly.It can withstand continuous moderate impact and can provide composite plates of various thicknessesNyaunglebin,→ the two surfaces of the flange are parallel to each other making it easy to connect, process and install.I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure.→ the two surfaces of the flange are parallel to each other, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm process and install.

The specification of I-beam is expressed in cm of waist width. For example, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Cold.→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing.Application processWhether I-section steel is ordinary or light,KadanQuotation of high pressure alloy pipe, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.

Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.Installation conditions,H-shaped steel groove is deep and thick, and can withstand forces in two directions.The advantage of the reinforcement mesh system is ecological. It is filled with natural stone materials. There is a gap between the stone materials to allow plants to grow in it. It can also plant plants on it. It has the dual effects of engineering slope protection and plant slope protection. The Ecological Grid mat is a combination with a height of cm ~ cm, mostly a multi grid box separated by spacer mesh.H-shaped steel groove is deep and thick, and can withstand forces in two directions.Kadan,Application characteristics of I-beamWhen it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.