HanshanOutdoor cargo elevatorGood service

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The last thing to note is that, compared with the lifting platforms in some places, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Hanshan,The maintenance of the elevator should be refueled regularly: During the use of the elevator, because of the relatively large load, the friction between the various components is also relatively large, especially the elevator chain and the elevator shaft pin. It is necessary to ensure that an appropriate amount of oil is added before each use to ensure It is flexible and not stuck when running work. If the elevator is running once there is a 'squeak' friction sound, it can be basically concluded that the elevator is short of oil, and the work must be stopped immediately to find out the reason and not to force the operation, which is likely to cause unforeseen hidden dangers. Point summary: Maintenance of elevators requires regular refueling,Hanshan3 ton fixed lifting cargo elevator, which is not allowed.After the goods are transported, clean up the debris on the platform.Zomin,The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable,HanshanWorkshop lifting cargo elevator, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.In the process of developing the guide rail elevator machinery, in order to ensure the use of the heavy platform under safe conditions and maintain compliance with relevant rules and regulations, the heavy platform is specially formulated, and the safety operating procedures are formulated as follows: It must be equipped with qualified and certified lifting equipment.Professional operators who are qualified and certified to work on lifting platforms. Operators working on lifting platforms should wear safety belts. When working in a live area, the car body should be grounded according to regulations. The climbing operation of the heavy platform should be commanded by the operator, and the operator should communicate with the operator of the heavy platform according to the standard signal. The announcement signal should be clear and accurate. The guide rail lift is safe and convenient to use. The guide rail lift usually lifts the lower arm first, then the middle arm, and then the upper arm. During the reversing operation of the lifting platform the lower arm must be reversed after being raised and lowered at a certain height. Inversion response is slow. Pay attention to whether the distance between the scissor arm and the platform meets the safety requirements of each equipment. For a long time, we provide all kinds of elevator factories for individuals and enterprises across the country, settle accounts on site, and have offices in various places for long-term cooperation.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Discount,System: explosion-proof electronic control system, remote control system, P IC system.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole and tighten the inner hexagon. After that, remove the motor shaft key.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time,Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.It is forbidden to stay under the high-altitude operation site, and safety nets or other protective devices should be installed under the work site to avoid injury caused by falling objects.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height but at present, hydraulic lifting platforms are more widely used.Hanshan,Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding,HanshanRail lift cargo elevator, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.