FenyangHydraulic unloading and tipping machineQuality improvement

There are dedicated operation buttons for firefighters at appropriate positions at the entrance of the first floor elevator. The operation buttons are generally protected by glass sheets and have a red&# quo; mark in place; Dedicated to fire protection; Words such as.The mechanical components of the elevator's traction machine require oil. There are two scales on the outer cover of the traction machine. Open the oil nozzle to check that the oil should be in the middle of the two scales. If the oil is lower than the lower scale, it means that the traction machine should be refueled. If not refueled, the elevator will not operate well for a long time, leading to the burning of the elevator traction machine and motor. After the elevator has been running for a long time, the oil should be replaced in a timely manner to keep the traction machine clean and in good condition.Fenyang,Slide elevators are installed inside buildings and are often used parallel to buildings and sidewalksThe requirement for the shaft is that it should not be plastered, which is beneficial for reducing noise,During the use of elevators, some elevator users seek temporary workers or unqualified companies for elevator maintenance in order to reduce costs and save funds. Once safety issues arise, even the responsible unit cannot be found. If the maintenance is carried out by elevator manufacturers or qualified professional companies, on the one hand, the maintenance technology and quality are guaranteed, and on the other hand, if any problems occur, someone is also responsible.The call button on each floor is no longer working and the call is cut off.The effective support width of the upper and lower support beams should be greater than the width of the escalator truss, and there should be embedded steel plates.

If the elevator is in a downward direction, immediately close the door and return to the first floor station, and to prevent skirts or pants from getting stuck.To implement the arrangement of escalators and provide feedback, in order to determine the configuration of certain shared devices,FenyangAluminum alloy mast type lifting platform, the order of shipment, and the alignment of handrail turns during continuous arrangement.Supply chain quality management,b. When the old elevator cannot start: due to the inability to enter the shaft, limited data can only be obtained from outside the shaft to determine whether it is non-standard (if there is a high platform in the machine room, the plane size of the shaft can be measured in the machine room, but it is not accurate enough) for elevator quotation negotiation reference. In this case, the signing of the contract should state that the shaft rectification and costs are the responsibility of the user. For uncertain shaft structures and dimensions, users should be reminded to provide them to the elevator after the old elevator or notify the elevator to take measurements before the new elevator is put into operation.The beam edge distance is too small: The method of shortening the lower platform is to shorten the total length of the escalator,FenyangVertical obstacle free lifting platform, but note that the range of shortening is very limited, generally not exceeding mm. Generally the platform cannot be shortened because it contains equipment such as cabinets and motors. Change the angle of the escalator from degrees to degreesDuring the use of elevators,FenyangFixed stage elevator, some elevator users seek temporary workers or unqualified companies for elevator maintenance in order to reduce costs and save funds. Once safety issues arise, even the responsible unit cannot be found. If the maintenance is carried out by elevator manufacturers or qualified professional companies on the one hand, the maintenance technology and quality are guaranteed, and on the other hand, if any problems occur, someone is also responsible.

Restore the command button function in the cabin for firefighters to operate.Customer first,b. When the old elevator cannot start: due to the inability to enter the shaft, limited data can only be obtained from outside the shaft to determine whether it is non-standard (if there is a high platform in the machine room, the plane size of the shaft can be measured in the machine room, but it is not accurate enough) for elevator quotation negotiation reference. In this case, the signing of the contract should state that the shaft rectification and costs are the responsibility of the user. For uncertain shaft structures and dimensions, users should be reminded to provide them to the elevator after the old elevator or notify the elevator to take measurements before the new elevator is put into operation.When encountering abnormal elevator operation, you can call the repair hotline to consult with the maintenance personnel or inform the service center to handle it. Do not take unauthorized measures to avoid causing greater harm to the elevator or even causing casualties.The door closing button has no self maintenance function. During the designated maintenance period, the elevator components in operation are inspected, refueled, and safety devices are debugged. Including non-destructive testing and maintenance of elevator traction steel wire ropes.Fenyang,If the elevator is already on the first floor, immediately open the elevator door and enter the firefighter's dedicated state.The front room of the fire elevator is equipped with indoor fire hydrants.Machine room power supply: The power supply should be three-phase V, HZ, and the lighting power supply should be single-phase V, HZ. The incoming line should be connected to the vicinity of the machine room entrance and equipped with an incoming socket. Specializing in product and renewable resource business, including: home elevator manufacturers