HajidunasElevator enterpriseThe temperature is out of control because what problems are not handled well

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Hajidunas,Advantages of operating cost: Low failure rate, due to the use of advanced hydraulic system and good methods, the failure rate of elevator operation can be reduced to a minimum. Less power consumption: When the hydraulic elevator goes down, it is driven by the pressure generated by its own weight, which greatly saves energy.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory old brand, price advantage, quality guaranteed!Dano,Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly,Hajidunas3-meter cargo elevator, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Secondly,HajidunasWhere can I sell elevators for goods, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean,Hajidunas4-ton cargo elevator, and the travel switch points of each safety device must be safe and reliable.

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Pay attention to heat dissipation when the motor works in a hot environment.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.superior quality,In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements with a load of up to tons.System: explosion-proof electronic control system, remote control system, P IC system.

Are the water cooling and air cooling of the hydraulic station the same?Project scope,What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt it must be washed off with gasoline or thinner.The main categories of aluminum alloy lifts in the Chinese market are based on the structure of the aluminum alloy lifts. The load is generally below kg, especially suitable for one-person operation.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.HajidunasMechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.