Chula VistaVertical slurry pumpHow to work in a humid environment without rust

　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should chooseChula Vista,　　With the features of installation and automatic control, it has a unique effect in discharging solid particles and long fiber garbage. For example, the common rexwell WQ series submersible sewage pump with runner impeller structure has good over-current performance, which can effectively reduce blocking and winding faults and greatly improve　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.Ujida,　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops and pay attention to the temperature rise outside the packing chamber.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness,Chula VistaScrew deep well pump, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.

　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, the packing of the vacuum pump leaks seriously and the gate valve or flap valve is not closed tightly.　　 Determination of flow　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, make the bearing components move forward, and roll the shaft by hand to press theSafety production,　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment,Chula VistaVertical multistage centrifugal pipeline pump, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller

　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.Installation material list,　　Other ysts believe that, at least in recent years, the situation of power shortage will continue and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, and the flow passage parts of this kind of slurry pump can be made of two materials, one is wear-resistant metal material, the other is wear-resistant rubber material. According to the working conditions, senior engineers of Panshi pump industry can select and design for you; For example,Chula VistaCirculating hot water pipeline pump, ZJ series　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, which will cause certain economic losses to us.Chula Vista,　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.