KayaDeep well pumpSurface protection techniques

KayaRubber lining submerged slurry pump, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impellerKaya, self priming is an action and a process). Only the self-priming pump can have the self-priming .　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certainHaimenlinna,　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, make the bearing components move forward, and roll the shaft by hand to press the　　The Tao part also consumes part of it.

　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,　　Structural features of horizontal slurry pump: The ah, HH and L-type slurry pumps at the pump head are of double pump shell structure, that is, the pump body and cover are equipped with replaceable wear-resistant metal lining, and the flow passage components such as impeller, sheath and guard plate are made of high chromium wear-resistant metal. The pump body and cover are made of grey cast iron according to the working pressure　　In fact,KayaBaigang deep well pump, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it tooreform,　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.

　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.how much,　　Rate.　　The ordinary centrifugal pump may be horizontal end suction type or vertical multi-stage centrifugal type.　　Different installation requirements: the vertical slurry pump needs to be fixed while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.Kaya,　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.　　Moreover,KayaVertical multistage centrifugal pipeline pump, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.