SonghuQuotation slurry pumpUrban application analysis of

　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.Songhu,　　The reaction force will make the axial motor end of the pump retract, which can directly damage the dynamic and static rings of the mechanical seal.　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pumpPuente Alto ,　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition,SonghuVertical heavy-duty slurry pump, the application market of submersible slurry pump is also better than that of vertical pump　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment,SonghuVertical slurry pump, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.

　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.　　After the submersible slurry pump is connected, it is necessary to shake the insulation resistance and observe its change when going down the well to prevent the insulation skin of the cable from being damaged by the well wall. If the insulation is found to drop rapidly below . megohm, the device shall be lifted to find out the cause. Because the submersible slurry pump is often used　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.packing,　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　There are differences.

　　Rate loss, so shaft power = effective power + lost power.Safety and health,　　When using the submersible slurry pump we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　Suction lift refers to the distance within the suction depth at the inlet of the pump when there is water in the inlet pipeline but there is no positive pressure at the inlet (quantifier, all centrifugal pumps have suction head in length). In fact, but the length is different. In a word, those with higher head have suction head　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, cut off the power supply of the motor. If the temperature of the environment is low open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodySonghu,SonghuWear resistant slurry pump,　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.