MinamirinkanVertical heavy-duty slurry pumpPrecautions in use

　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?Minamirinkan,　　 Check and replace accessories regularly: check cables, motor insulation and screws at least once a year. If it is damaged, it should be replaced in time.　　The structure of the submersible slurry pump will be more intuitive. First,MinamirinkanWQ submersible pump parameters,MinamirinkanSingle stage slurry pump, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speedAl Harak,　　At the same time, clean the part to be bound with alcohol again and wipe it dry.　　Do not exceed the rated current.

　　In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the configured cable is relatively thin, so the voltage drop is too large, and it is difficult to start the submersible pump. A larger cable is required. If the distance is long, the submersible pump should be close to the transformer.　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.Direct material,MinamirinkanPipeline pump,　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.

　　 First of all let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationHonest service,　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　Whether the pipeline pump can absorb water and whether the pipeline pump has self-priming depends on the model of the pipeline pump. Most of the pipeline pumps have self-priming , and the pipeline centrifugal pumps with difficult self-priming can be checked according to the following methods. For longer use　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.Minamirinkan,　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.