Jade SpringVesperThe difference when using

To meet the needs of choreographers and choreographers in different plays, different heights of the lifting platform can be used to change the shape of the stage according to the requirements of the choreographers and choreographers,Jade Springzabul , in order to adapt to the requirements of the plot for the scenery or venue, and save manpower and material resources for setting up. By using the tilting device of the lifting platform to form a tilted platform, a better highlighting effect can be achieved in various performances. According to the needs of the plot, special atmosphere and effects can be created. Even simple stage machinery often participates in performance activities, creating unexpected atmosphere and effects according to the needs of the plot. For example, using the low-speed descent of the lifting platform to represent a sunken ship in the sea, using the valves on the lifting platform and the sudden disappearance and appearance of actors on the lifting platform.The setting of the cable guide frame should comply with the user manual and regulatory requirements.Jade Spring,A lifting platform with specifications ranging in height from meter to meters.Drainage measures need to be considered around the foundation. (Drain the accumulated water on the foundation).Guadalupe,Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, and ensure that the lifting platform can be lifted to the rated lifting height.Horizontal lead screw mechanical electricityThe use of standard section connecting bolts should comply with the user manual and specification requirements.

Before operating the construction electric elevator, routine inspections should be carried out according to regulations and inspection records should be filled out.Construction electric elevators should be equipped with travel limit switches,Jade SpringHartwan, as follows: automatic reset type upper and lower limit switches should be installed on construction electric elevators, but the upper and lower limit switches should not be triggered as highThe net height of the landing door opening should not be less than m, and the difference between the net width and the outlet width of the cage door should not exceed mm. When the floor door is closed, except for the gap between the lower part of the door that should not exceed mm, the size of any through-hole and opening related to the distance between any door and adjacent moving parts, as well as the gap around the door or between parts, should comply with the provisions of Table of 'Mechanical Safety - Safety Distance to Prevent Upper and Lower Limbs from Touching Dangerous Areas' GB-.Equipment maintenance,The motor of the hydraulic guide rail lifting platform is set around the wellbore, occupying a relatively small area, improving the utilization rate of the wellbore area.Construction electric elevators outside the lightning protection rangeDuring normal operation, the horizontal distance between the closed cage door and the closed landing door should not exceed mm. Otherwise measures should be taken to make it meet the requirements, or side protection devices at the entrance of the landing station that meet the requirements should be equipped. The distance between any opening between the side protection device and the hanging cage or landing door should not exceed mm.

Chain type electric lifting mechanism: With a good guiding mechanism, it can ensure that the equipment does not tilt during operation. Gear and rack electric lifting mechanism: precise transmission and high cost.Create brilliance,Setting requirements: The verticality deviation of the installation of the guide rail frame of the construction electric elevator should comply with the requirements of the user manual and specifications as specified in the above table.Normal operation starts. Click on this free download of construction technical information. Safety limit devices should be installed on electric elevators for construction,Jade SpringPSV Eindhoven, with upper and lower limit switches that are sensitive and reliable.Installation and dismantling personnel and drivers should hold certificates to work.Jade SpringThe connection method and angle between the wall bracket and the building structure should comply with the requirements of the user manual.Setting requirements: The verticality deviation of the installation of the guide rail frame of the construction electric elevator should comply with the requirements of the user manual and specifications, as specified in the above table.Stage equipment safety door. To prevent personnel from extending their heads, hands, its cabin should be full of doors, and the height of the hoistway (hall door) should not be less than meters; The electric door opening and closing switches should be removed from the vertical and passenger compartment doors. In order to prevent accidents caused by vertical, passenger car doors, and car roof doors not being closed.; Door interlocks should be installed on both the vertical and passenger compartment doors.