Sadat sindiaWater well pipeline pumpQuality improvement

the pump shall be lifted away from the water source in time to drain the accumulated water in the pump

　　When the pump is not in use, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.Sadat sindia,　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation, and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller, conical sleeve and remove the guide housing. In this way,Sadat sindiaSingle suction slurry pump, the impeller, guide housing upper guide housing, check valve, etc. are unloaded in turn.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.Delicias,　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　Submersible slurry pump can be widely used in mining, power, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, etc. In chemical industry　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.

　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　After the submersible slurry pump is connected, the device shall be lifted to find out the cause. Because the submersible slurry pump is often used　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even ifequipment maintenance ,　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump,Sadat sindiaDouble suction slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpLatest consultation,　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.　　The water pump spindle is bent, and the spindle is not parallel to the motor spindle.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.Sadat sindia,　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.　　 Next, the water seal, lock ring and other parts need to be installed.　　After meters, the sealing of the equipment can not bear the water pressure at this depth.