EvlerCylinder mounted hydraulic lifting platformHow to operate during construction

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Next, the hydraulic cargo elevator manufacturer will explain the maintenance of the mechanical equipment of the elevator: the brakes of each organization should be frequently checked and adjusted to ensure the clearance between the brake pads and wheels is sensitive and reliable. On the surface, there should be no dirt present. If there is dirt, it is necessary to wash it off with gasoline or thinner.Evler,In case of strong wind of level or above, rainstorm, thunder, fog and other bad weather,Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete, and ensure the smooth progress of the installation process.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, the pre installed equipment should be fixed, and the positions of cables, oil pipes, and the hydraulic cargo elevator after reinforcement has robustness and safety.The manufacturer of hydraulic cargo elevators tells you the precautions to be taken when installing hydraulic cargo elevators. Hydraulic cargo elevators work using hydraulic systems and are usually used for the transportation of large goods. Hydraulic cargo elevators are different from traditional shelf elevators. They use a new hydraulic system to reduce the occurrence of faults and utilize their own weight to reduce energy consumption when lowering goods. So, what should be paid attention to when installing hydraulic cargo elevators? The hydraulic cargo elevator manufacturer is here to tell you!After hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.Free consultation,The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.Separate: Loading and unloading on different platforms.

Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)Installation worksWhen the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.Generally speaking for situations with large lifting loads and small lifting heights, a lifting mechanism should be selected. For situations with small loads but large lifting heights, a lifting mechanism should be selected. According to the initial structure of the jacking, in order to meet the stability requirements, the size and lifting type of the oil cylinder are increased, and in order to achieve the same effective area as the jacking force, the oil cylinder is added. If the latter is larger, a lifting mechanism should be selected.When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner, clean the problem,EvlerHydraulic lifting platform, and continue running. The motor bearings should be smooth and outstanding.Evler,If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.When using hydraulic elevators, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).For hydraulic cylinders in hydraulic elevators,EvlerMechanical hydraulic lifting platform, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.