SenicaEffect drawing of red wood floor decorationThe importance of each value material

Skin allergy.The flame retardant grade is B, and the indoor formaldehyde meets the national industry standard.Senica,Then select one or more floor waxes, which can be adjusted to the same tone as the floor.Heat the strip solid recovery wax with an electric soldering iron and fill it on the scratches on the floor. No scratches can be seen.Mute, that is, add cork cushion or other cushion similar to cork on the back of the floor.After using the cork floor mat, the noise of stepping on the floor can be reduced by more than dB (quoted from the data of the cork floor mat factory), sound absorption and sound insulation.This plays a positive role in improving the comfort of laminate flooring.It is also a direction for the future development of laminate flooring.Taugefpiers,SPC floor is an excellent raw material with the advantages of wear resistance, durability, low carbon and environmental protection.It is widely used in various indoor places.Including diagnosis and treatment, sports culture, colleges and universities, culture and education, kindergartens, business services, offices etc.The shadow of SPC floor can be seen.SPC floor is an excellent raw material with the advantages of wear resistance, durability,SenicaFloor tile,SenicaWhen will the floor be installed better, low carbon and environmental protection.It is widely used in various indoor places.Including diagnosis and treatment, culture and education, kindergartens, business services, offices, etc.The shadow of SPC floor can be seen.Melamine surface coating is generally used for wallboard tabletop board, etc. it is used in places with low wear resistance requirements. In the flooring industry, this kind of surface coated floor is called 'false floor'Its wear-resistant revolution is only - revolutions. If it is used with high strength, the decorative paper on the surface will wear out after two or three months. The standard laminate floor will not have such a problem after years of normal use. There is no wear-resistant layer on this kind of floor decorative paper, the pattern is beautiful and clear, and it is relatively smooth when touched by hand, which is the place where laymen are easy to be fooled.

The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree the tool cost during processing is also low. On the contrary, Establish the interior decoration style you want: if you expect simplicity and warmth, choose the sexual or shallow floor as much as possible, and if you expect calm air, choose the dark floor.The surface coating of piano paint is actually the paint used on the surface of solid wood floor for laminate floor. It is only bright paint. The wear resistance of this coating is far from that of aluminum oxide surface. Its wear resistance is low, and solid wood floors are developing towards high wear resistance. Unless you like the coating of this surface.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat,SenicaWhich is better, solid wood composite floor or solid wood floor, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, Anti skid. Compared with ordinary floor materials, the nano fiber feels more astringent when it is exposed to water and is less likely to slip. The more it meets water, the more astringent it becomes.It is suitable for families with old people and children. It is the preferred ground material in public places with high public safety requirements such as airports, hospitals, kindergartens, schools, etc.Looking at the bar code formal reinforced composite floor, the back of the floor will be printed with not only the brand trademark, but also the model, wear revolutions, environmental protection grade and other information of the floor, so that consumers can see it at a glance. Non toxic and tasteless, not afraid of water, fire and tide;In terms of scratch resistance, resource use and anti-skid performance, SPC floor is better than laminate floor.Senica,： I can smell faint wood fragrance. This floor shows that the glue content is very low.Up to European standard E level.Precautions for solid wood floor installation : avoid the inconsistency between the length direction of the floor and the entrance direction.Common types: three-layer solid wood composite floor, double-layer solid wood composite floor, new solid wood composite board.