KercladElectric self hydraulic lifting platformAbout job characteristics and the existence of risk factors

To reduce noise, increase the clearance inside the platform, and also make the transmission more stable and the mechanism vibration less.Strictly follow the operating instructions of the elevator for safe use and strictly prohibit illegal operations.Kerclad,After assembly and debugging, roll and move the nut to the left end of the bolt and tighten the half round head bolt. Adjust the position of the collision rod up and down based on the lifting degree of the landing elevator platform, so that when the lifting degree of the landing elevator platform exceeds the predetermined height move the nut to collide with the collision rod and roll it clockwise. Push the limit switch contact to cut off the power supply.Furthermore, it is necessary to raise and lower the elevator several times at regular intervals to ensure that the hydraulic oil inside and the grease on the components are not misaligned due to prolonged immobility. It is also important to pay attention to the operation of the components to be observed. If the temperature is relatively low, it is necessary to frequently check the hydraulic oil of the elevator. If it is abnormal, it should be replaced with new hydraulic oil in a timely manner. Mechanical maintenance should also be done well, otherwise oxidation and deterioration may occur and cause damage to the elevator. Specializing in product and renewable resource business, including mobile elevator manufacturersSanta-Clara,KercladHydraulic lifting platform,Drain and discard the hydraulic oil, tighten the joint, remove the oil filter, clean it with compressed air, and then return it to the oil tank and connect the pipeline.Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Fill the above components with oil. The service life of bearings can also be greatly enhanced.The elevator features and advantages of a smooth and repair free pivot, with built-in lanyard fixing points. An ergonomic joystick that can be operated from a platform or ground.

And different uses: single column electric elevators: This series of products is indoor and widely used for high-altitude operations in various industries such as star hotels and large supermarkets. It has balanced lifting and easy operation, and can enter general lobbies. It can enter and exit the elevator at will with low power consumption, no pollution, and does not harm the ground during work. It can be used for wall work and exploration work, without dead corners. The single column electric elevator equipped with a gantry cross frame accessory, is very suitable for maintenance work in cinemas, auditoriums, etc. The gantry frame is easy to assemble, flexible to move capable of crossing obstacles such as fixed seats with a height of up to m, and can operate stably on steps. Made of high-strength rectangular steel pipes, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.During the trial load, multiple tests should also be conducted. For the second trial load, whether the stability of the platform meets the requirements, whether the sound is normal, and whether the rated lifting height can be reached. If the test data is normal, a second trial load test can be conducted; The second trial load test can choose half load test, with a focus on verifying the stability of the platform. If the shaking resistance is within the allowable range, a third test - full load test can be conducted to determine whether all parameters of the platform are normal under the rated load state. If it is normal the fourth test - overload test can be conducted, and % of the load can be added for the test to verify whether the anti overload device setting of the platform is reasonable. If the setting is correct, the lifting platform cannot rise under overload. If it can rise, it indicates that the overload device setting of the lifting platform is unreasonable, and the manufacturer should be asked to adjust the setting again.And different uses: single column electric elevators: This series of products is indoor and widely used for high-altitude operations in various industries such as star hotels and large supermarkets. It has balanced lifting and easy operation, and can enter general lobbies. It can enter and exit the elevator at will with low power consumption, no pollution, and does not harm the ground during work. It can be used for wall work and exploration work, without dead corners. The single column electric elevator, equipped with a gantry cross frame accessory, is very suitable for maintenance work in cinemas auditoriums, labor-saving to operate, flexible to move, capable of crossing obstacles such as fixed seats with a height of up to m, and can operate stably on steps. Made of high-strength rectangular steel pipes, with good rigidity and stability. Equipped with universal casters for flexible mobility. The span of the two end brackets can be adjusted, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.High quality and low price,At the end of the year, many customers called to inquire about elevators. During this time of year, various units need to hang lanterns, etc. Many customers do not know how to choose a suitable elevator. Below is an answer for everyone. Lifts can be generally divided into three types: manual traction mobile lifting and lowering platforms: This type of lifting platform is cost-effective, cheap, and widely used, When moving, it requires manual traction or mechanical pulling from a car, and when lifting, it requires an external V or V power supply to lift.Elevators play an important role in handling, construction, and other operations, providing convenient transportation equipment. More and more elevators are being put into use in the market, but unstable voltage can have a certain impact on elevators during use.Characteristics of elevator form:.

The equipment is equipped with leakage protection switches, emergency stop switches, extreme electrical limit switches, etc. The button boxes are all waterproof in design.quality,KercladElectric hydraulic lifting platform,Attention must be paid to the rotating parts of the elevator. When the engine is running. Hands and tools must be kept away from rotating fan belts and fans. During the test drive, it is necessary to be in a spacious area and ensure that the aluminum alloy elevator can safely stop and turn effectively.The higher the number of masts, and the greater the stability load on the platform.Drain and discard the hydraulic oil, tighten the joint, clean it with compressed air, and then return it to the oil tank and connect the pipeline.Kerclad,The entire elevator is made of high-strength aluminum profiles, which have high strength, beautiful appearance, small size, light weight, compact structure convenient movement, stable lifting platform, and are suitable for use in factories, hotels, buildings, shopping malls, stations, airports, sports venues,KercladElectric hydraulic platform lift truck, etc.Furthermore, it is necessary to raise and lower the elevator several times at regular intervals to ensure that the hydraulic oil inside and the grease on the components are not misaligned due to prolonged immobility. It is also important to pay attention to the operation of the components to be observed. If the temperature is relatively low, it is necessary to frequently check the hydraulic oil of the elevator. If it is abnormal, it should be replaced with new hydraulic oil in a timely manner. Mechanical maintenance should also be done well, otherwise oxidation and deterioration may occur and cause damage to the elevator. Specializing in product and renewable resource business, including mobile elevator manufacturersLifts are a product of modern high-altitude operations. During their development, the performance and quality of elevators have continuously strengthened, becoming the main force of modern high-altitude operations. So, how much do you know about their scientific design solutions?