Sherwood Park Screw deep well pumpWhat if we want to improve the efficiency of processing

　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.Sherwood Park ,　　It can be that there is water leakage in the pipe gasket, pipe or pump body. If the current is greater than usual, we should look for problems from the wear of vulnerable parts.　　If the oil seal ring of the shaft is seriously worn replace it with a new one.Gaoua,　　When in use it can drive the impeller to rotate so as to drive it to flow.　　 When adding lubricating oil to the pump at ordinary times, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.

　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping,Sherwood Park Ah slurry pump, so that the sand pumping area in this area forms a honeycomb,　　If the sewage contains fiber objects such as gloves, we suggest that the cutting submersible sewage pump with cutting is more appropriate; WQ submersible sewage pump can only transport Ordinary sewage. Excessive solid content in sewage leads to infarction. It can be applied to wqk submersible sewage pump with open impeller structure　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment,Sherwood Park Carbon steel explosion-proof pipeline pump, and the current will slowly increase during use. Well, we should chooseQuotation sheet,　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness, concentration, acid, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placesWelcome calls ,　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　 Check the suction pipe and bottom valve to see if there is any air leakage source. Remove the silt and other obstructions at the water inlet. Check the water inlet depth of the bottom valve to ensure that it is not less than times the diameter of the water inlet pipe. If it is not enough, deepen the water inlet depth of the bottom valve.　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect,　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names,Sherwood Park Screw deep well pump, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　It is an auxiliary means for some on-site monitoring.