HaibuHow much is precision welded pipeQuality Standard

Key technical characteristics of alloy pipe:As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally : which makes the outer flange thin and the inner flange thick. Therefore, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market the section characteristics of I-beam in the two main planes are very different, the structure of the I-beam has determined its torsional performance.Haibu,The electric welding reinforcement mesh can reduce the damage and consumption to the reinforcement processing process. According to statistics,HaibuGH3030 superalloy tube,HaibuHow much is a meal, after deducting the steel consumption increased by unit lapping, it can also save about % of the steel. After it is transported to the site according to the construction degree of the project, it can be hoisted to the working face. There is no need to set a reinforcement processing site on the site, which saves the site and increases the management level of the site. At the same time, it can also solve the problems of noise pollution caused by straightening reinforcement.Application characteristics of I-beamCochin ,Introduction to product knowledge of alloy pipe:Classification introductionAccording to the theory of steel structure, that is, the I-beam should be standing rather than lying down.

Function of I-beam: where is I-beam mainly used?The smooth of steel pipe is mainly through tension reducing, which is a continuous rolling process of hollow base metal without center and tip. Under the condition of ensuring the capillary welding quality, the whole welded pipe is heated to more than ℃ by the welded pipe tension reduction process, and then rolled to finished pipes with various outer diameters and wall thicknesses by the tension reduction machine ( times in total). The fluid pipes produced by developed countries in the world have adopted the welded pipe smooth process in a large number of boiler pipes. With the development of society, Domestic hot welded pipe has gradually formed a situation to replace smooth pipe.In order to make the steel pipe workpiece have the required mechanical,HaibuAlloy pipe GH3030, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.production, The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.→ the two surfaces of the flange are parallel to each other, making it easy to connect, process and install.What should we pay attention to in the production of alloy pipe

Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy, radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope, mold shell and software requirements, which are very simple, and relatively low product cost. The processing time is not long enough, the processing capacity is not high the total length of processing pipeline is limited, and the size of machinery and equipment is generally short.Direct material,What should we pay attention to in the production of alloy pipeGalvanized pipe is often seen in our daily life, especially in some construction sites. This product has the advantage of durability when used. It also has the characteristics of surface gloss, the cost of hot-dip galvanizing for rust prevention is lower than that of other paint coatings. In addition, this product also has the characteristics of no dripping, strong adhesion, breaking the clean Legion and strong corrosion resistance. Even if it is used in some places where the environment is not good, its service life is also very long, and it also has the characteristics of corrosion resistance. The standard anti rust thickness of hot-dip galvanizing can be maintained for more than years without repair. This is used in some suburban environments. However, in urban or offshore areas, standard urban or offshore areas can be maintained for years without repair. The products produced by our company must meet these requirements. Friends who need to order can call us directly.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Haibu,I-beam is widely usedAfter isothermal quenching treatment, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.