ChiryatDeep well submersible pumpInject new momentum into industrial development

　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　 Then reinstall the equipment on the engine and install the rubber hose.Chiryat,　　This series of slurry pumps are self-developed slurry pump products in China, with simple structure, belonging to medium and light slurry pumps; ZGB series slurry pump, this series of slurry pump is a heavy-duty slurry pump, which can be used in series; When SP and ZJL series work, some pump bodies can　　Work, no noise and vibration, and the site is cleaner.Sasolburg,ChiryatSubmersible non clogging slurry pump,ChiryatSubmersible slurry pump,　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, so there will be no buried pump when it is used. However,　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.

　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　 There are several reasons for the severe vibration of the pump body: the phenomenon of unbalanced rotation of the electric rotor.　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.reform,　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less and the efficiency of the pump in use is often improved, and the fact is　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time

　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.Range,　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　Control type Liquid level control: the control cabinet is equipped with a high-performance key float switch to automatically control the start and stop of the water supply and drainage pump according to the high and low changes of the liquid level.　　 When adding lubricating oil to the pump at ordinary times,ChiryatSubmersible non clogging sewage pump, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.Chiryat,　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it