TulsaFire deep well pumpInspection requirements for

　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose　　Water flow into the bearing damages the bearing.Tulsa,　　There are main reasons why the submersible pump is 'sick'. The rotation direction of the motor is wrong: please ensure that the rotation direction of the motor is correct before using the submersible sewage pump. Even if water is produced by reverse rotation, the output of water is small and the current is large. Direction rotation will cause irreversible damage to the motor winding　　It will generate heat, but when it is serious it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingHaskovo,　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.

　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area,TulsaSelf priming slurry pump wholesale, so there will be no buried pump when it is used. However,TulsaPipeline pump body,　　 altitude of pump installation site M　　Adjustment. When using the submersible slurry pump, which will cause equipment problems and affect work efficiency. So we&#;re usingQuality management,　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.

　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurryHonest service,　　As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, especially meeting the needs of deep-water sand pumping and dredging. At present the depth can reach meters.　　Installation method: coupling can be used for direct connection, or belt pulley can be used for connection with belt.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation but also cause serious damage to the equipment itself,TulsaVertical multistage centrifugal pipeline pump, so it is also a reminder that we are using it tooTulsa,　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Only in this way can its service life be extended to a large extent.