SaskatoonVertical heavy-duty slurry pumpDiscuss the design characteristics of

　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　At the same time, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Saskatoon,　　 particle size (maximum and minimum) mm　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.Pumi veal,　　The whole packing body, including the packing gland,SaskatoonVertical slurry pump, packing ring and packing needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　Be sure to choose a pump that is more suitable for use.

　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　Automatic pump failure: cause: A. whether the frequency converter has abnormal symbols; b. Whether the actual pressure is higher than the set pressure.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore,SaskatoonBooster pipeline pump,SaskatoonUsed pipeline pump, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.How much is it,　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be great　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged

　　The utility and durability of the utility model, so the polymer composite materials are generally used in production.ranking,　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.　　Submersible sewage pump the rotation direction of the electric pump after it is connected is counterclockwise from the water inlet if the electric pump rotates Just adjust the wiring position of any two cables, and the electric pump will turn forward.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium so that the equipment can be used without itsSaskatoon, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.