OdderWuxi stainless steel beltHow to distinguish between good and bad quality

Martensitic stainless steels typical martensitic stainless steels include Cr ~ Cr and Cr, which have good processing properties. Deep drawing, bending, crimping and welding can be carried out without preheating. Crl does not require preheating before cold deformation, but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, while crcr is mainly used to make surgical and wear-resistant parts of medical instruments; crl can be used as corrosion-resistant bearings and tools.The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, and the pipe end is relatively sharp to prevent direct contact with the sealing ring of the pipe fitting. It is necessary to cut off a small section at both ends of the pipe or grind off the corner edge with a hand grinder, and then clamp the pipe fittings.Welding of stainless steel pipe argon arc welding stainless steel pipe: it is required to have deep penetration, no oxide inclusion, and the heat affected zone can be as small as possible. Argon arc welding maintained by tungsten inert gas has good compliance, high welding quality and good penetration function. Its commodities are widely used in chemical, nuclear and food industries.Dosso,Meet the needs of architects and structural designers.Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, and HRC is second only to Brinell hardness Hb in steel pipe standards. Rockwell hardness can be used to measure metal materials from very soft to very hard, which makes up for the disadvantage of Brinell method, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However, due to its small indentation, the hardness value is not as accurate as Brinell method.Model & mdash& ldquo; Cutting tool level & rdquo; Martensitic steel, an early stainless steel similar to Brinell high chromium steel. It is also used for surgical tools, which can be made very bright. Model & mdash; Ferritic stainless steel for decoration, such as automotive accessories. Good formability but poor temperature resistance and corrosion resistance.

It has the characteristics of high efficiency and low cost. At the same time, it can also well ensure the welding quality (in the capacity expansion and reconstruction project of Urumqi petrochemical, we use this method to weld joints and repair joints with a one-time qualified rate of welding), which is worthy of our use.The Chinese brand cold rolled non oriented silicon steel strip (sheet) represents: DW + times of iron loss value (at the frequency of Hz, and the magnetic induction peak is T per unit weight iron loss value) + times of thickness value. For example, dw- represents cold rolled non oriented silicon steel with iron loss value of W / kg and thickness of .mm. Now the new model is represented as W.Flux coated welding wire is used for backing welding, and argon gas is not used inside the weld. The welder's operation is simple and fastTrustworthy,For business people, of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, But I have to accept it. Next, xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.The accumulation of organic impurities caused by decomposition products and the pollution of some other metal impurities. There is no turnover of long-term stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe to avoid price difference. The price is % higher than the market price! The price of more than one ton is higher! So that the nickel bath can not get the ideal bright nickel coating, it is necessary to carry out large-scale treatment. In the solution of bright nickel plating on stainless steel pipe,Odder310S stainless steel plate, the brightener has developed rapidly and has many varieties. To sum up, the development of brighteners has experienced four generations. Instead of the original product, saccharin and butynediol can be plated with bright nickel with high flatness. Its application flourished in the s and s. It seems that due to the instability of butynediol in the nickel plating bath, short service life and rapid accumulation of organic impurities,OdderStainless steel mesh belt conveyor, the nickel bath needs to be treated frequently. Therefore, epoxy chloropropyl or epoxy is branched with butynediol to synthesize the second-generation nickel plating brightener, such as b brightener. The situation has improved. Be and retain alkynyl. Later, pyridinyl is polymerized to form the third-generation product, Faster light output, less amount of brightener and longer service life. Now it further uses various combinations of nickel plating brightener intermediates to form a new brightener, which has developed to the fourth generation of products. It has less use, faster light output speed and longer treatment cycle. According to the connection and rolling process, stainless steel pipes with deep plating capacity mainly include hot-rolled, it mainly includes semi Ferritic and semi martensitic stainless steel pipe, martensitic stainless steel pipe, austenitic stainless steel pipe, austenitic ferritic stainless steel pipe, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.

According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe hydraulic prop pipe,OdderStainless steel welded pipe, gas cylinder pipe, geological pipe chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.offer,Stainless steel has been used as a structural material for building new buildings and repairing historic sites for more than years. Early designs were calculated according to basic principles. Today, design codes, such as ANSI as of the American Society of civil engineers, are usedBefore connecting the pipe fittings, mark the depth on the pipe first, including the chemical fertilizer industry, has a great demand for stainless steel pipes. Stainless steel pipes are mainly used in this industry, including, , l, etc., with an outer diameter of about ￠ - ￠ and a wall thickness of about mm-mm (generally medium and low pressure transmission pipes with a specification of more than & phi; mm). The specific application fields are: furnace pipes, material transmission pipes, heat exchanger pipes, etc.Odder,Some reasons for product composition ratio: in order to reduce the production cost, reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time, they also affect the appearance and oxidation resistance of products.Stainless steel seamless steel pipe for structure (instead of gbt-)Welding, high frequency preheating plus three torch argon arc welding, high frequency preheating plus plasma argon arc welding. The progress of combined welding is very significant. As for the combined welding of steel pipe with high-frequency preheating, the weld quality is equivalent to the conventional argon arc welding and plasma welding, the welding operation is complex, and the whole welding is easy to complete automation. This combination is easy to connect with the existing high-frequency welding equipment with low investment cost and good benefit.