AntibesScissor fork hydraulic lifting tableWhat is the factory way

AntibesHydraulic lifting platform frame,

The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.AntibesOil cylinder leaks. Long term use causes wear on the sealing ring in the oil cylinder and excessive oil leakage in the cylinder wall gap, resulting in the natural descent of the hydraulic cargo elevator. The sealing components need to be replaced immediately.The characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, and rear hinge support.Kolkhozobod,The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it should be suitable for the operating power.

Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.Hydraulic oil deteriorates or produces impurities. After long-term use of oil pressure, there may be impurities or deterioration in the oil. Sampling inspection should be carried out to see if there are solid particles, discoloration, and odor. If necessary, the oil should be changed. There may be blockage in the hydraulic pipeline of the hydraulic cargo elevator. The hydraulic pipeline is also a very important part, and it is necessary to check whether the hydraulic pipeline is smooth. Focus on checking whether each type of hydraulic valve includes one-way globe valve, electromagnetic directional valve, proportional control valve, overflow valve, etc. If there are problems, the hydraulic valve should be cleaned or replaced in a timely manner.New reference wiring diagram . Elevator leg noise. Mobile elevators should open the legs before operation. In this case, if the legs lack butter, noise will be generated.analysis,Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.

The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn,Antibes8-meter hydraulic lifting platform,The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects). The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed. To ensure safe and reliable braking and prevent accidents, a hydraulic control one-way valve, also known as a hydraulic lock is added to ensure safe self-locking in the event of an accidental rupture of the hydraulic pipeline. An overload sound control alarm has been installed to distinguish between overload or equipment failure.When working at heights, except for relevant personnel no one is allowed to walk or stay below the workplace. Fencing or other protective devices should be installed below the workplace to prevent falling objects from injuring people.What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators, ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety,AntibesScissor fork hydraulic lifting platform, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.Antibes,Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than %.