BayagunaWQ submersible pump parametersProfessional customization

　　Promote the continuous expansion of the sales network group.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.Bayaguna,BayagunaTwo stage slurry pump,　　Conduct a comprehensive preventive maintenance once a year, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome and the application occasions are subject to many restrictions.Kunka,　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, many pumps often have better measurement results when in use.　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration and the site is cleaner.

　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　 Requirements for complete set of water pump　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particlesMeticulous workmanship,　　However,BayagunaDeep well pump, there is also a disadvantage of using the auxiliary impeller sealing system, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　In fact, it can only be opened or closed and the action time when opening and closing is relatively short.

　　 strip the outer layer of the cable to expose the copper wire for to mm,BayagunaSubmersible slurry pump, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.The cheapest,　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too　　ZGB and other series, SP submerged slurry pump, SPR submerged rubber lined slurry pump, ZJL submerged slurry pump and other series, with complete models, flow passage parts and accessories; Third, from the number of impellers, the type of slurry pump is divided into single-stage slurry pump　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.Bayaguna,　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use