Kyle BridgeSubmersible sewage pumpHow to improve the pumping efficiency

　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller) magnetic dial indicator, outside micrometer, feeler gauge, square ruler, copper bar,Kyle BridgeSingle suction slurry pump, screwdriver with handle, hammer V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.Kyle Bridge,　　 Mechanical seal: mechanical seal is generally used when the sealing requirements are relatively high, especially in the chemical industry. It is not only required that the slurry should not leak, but also not allowed to enter the pump body. The disadvantage of mechanical seal is high cost and difficult maintenance.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Farola,　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, which can separate the pump body from the motor, so it mainly plays a role in use　　After meters,Kyle BridgeUsed pipeline pump, the sealing of the equipment can not bear the water pressure at this depth.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.

　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.　　The key to the problem should be to fundamentally solve the problems of pump sealing and overload, which is a more active method. Therefore, we applied the hydrodynamic seal technology of the auxiliary impeller and the non overload design technology of the pump to the submersible sewage pump, which greatly improved the pump seal　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump which can separate the pump body from the motor, so it mainly plays a role in usePursuit of excellence,　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, it needs to be replaced in time,　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.

　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Equipment maintenance,　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, and tighten the next section of water pipe with pipe clamping plate. In this way, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force, and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.Kyle Bridge,　　Other ysts believe that, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially　　Although the shaft seal occupies a small position in the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main