SanRafaelTop 10 brands of laminate flooringAppropriate method of industry construction

Ultra light and ultra-thin, which is less than % of ordinary ground materials. It has incomparable advantages in stair bearing and space saving in high-rise buildings. At the same time, it has special advantages in the reconstruction of old buildings.advantageSanRafael, Wear resistance level. Soak in waterJhang Sadr,Some people say this method is unscientific and laminate flooring can&#;t soak in water, but I have done some experiments and come to another conclusion.The flame retardant grade is B, and the formaldehyde concentration is acceptable.Precautions for solid wood floor installation : prevent uneven ground.Some people say this method is unscientific and laminate flooring can&#;t soak in water, but I have done some experiments and come to another conclusion.

The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Moreover, the formaldehyde in the floor mainly comes from the adhesives and coatings used in production.In order to improve the hardness of the board and have the effect of insect prevention and anti-corrosion, most artificial boards use urea formaldehyde resin as the adhesive. The main component is formaldehyde, and residual formaldehyde is inevitable.The environmental protection grade of domestic flooring is divided into E,SanRafaelWhich kind of domestic wood floor is better, E and E Only the flooring reaching grade E has a formaldehyde emission of no more than mg/l, which meets the requirements of national standards.Defects: small blisters can not be repaired after damage, and the upper foot is poor.plan,The crystal surface is basically flat. It&#;s easy to take care of and clean up.The current woodworking is basically done by woodworkers. The 'general woodworking' method is adopted, and the shrinkage joint size is not calculated according to the thermal expansion and cold contraction parameters provided by SPC flooring factory.If the room is slightly larger, but the reserved gap is too small, especially when the temperature difference between winter and summer is too large, it is very easy to have no gap to expand resulting in arching and warping.We hope these techniques will help simplify the plan for installing new floors.If you plan to renovate your house and add new floor elements, please provide room sizes free of charge!Obtain expert estimates to understand how many floors are needed to better determine the project budget.SPC floor is composed of thickened wear-resistant layer,SanRafaelLaminate brand, UV layer, color film texture layer and substrate layer.European and American countries call this kind of floor RVP (rigid vinyl plate), rigid plastic floor.The base material is a composite plate made of stone powder and thermoplastic polymer materials after mixing evenly and then extruded at high temperature. At the same time, it has the properties and characteristics of wood and plastics to ensure the strength and toughness of the floor.Wear resistant layer: PVC transparent wear-resistant layer, with a thickness of about .mm, transparent texture, strong adhesion, wear resistance and scratch resistance, and the wear-resistant coefficient can reach - revolutions.[]

The biggest highlight is that they are not afraid of water and shop willfully anywhere.How many?, Select machining accuracy Remove the residual glue and glue on the ground.Beautiful: it can simulate all kinds of wood grain, design and color on the computer.SanRafael, Generally,SanRafaelWhich is better, wooden floor or ceramic tile, wear-resistant paper with aluminum oxide content of about g / m is used, or wear-resistant paper is not used.Low density board (medium density board is rarely used), and the number of wear-resistant revolutions is usually between - revolutions.The edges and corners will be worn after being used for one or two years at most.With Hunan, Hubei Shandong, Liaoning, Jilin and Heilongjiang as the gathering points, not environmental protection, government departments are strictly investigating and dealing with it.Such illegal businesses only take into account short-term interests and have no after-sales service guarantee. The price ranges from to yuan.Generally, the moisture content of non dry wooden keel is about %, and that of qualified wooden floor is generally about %. If the humidity difference is too large the wooden floor is easy to absorb moisture quickly. If the time is long, the floor will arch up and the paint will crack.Therefore, it is best to choose dry and straight wood as keel.After the keel level is determined, the keel and floor can be fixed with nails. Smell: whether the product has a chemical smell that irritates people. The big smell is likely to be that the limit of harmful substances exceeds the standard or the printing layer on the surface of floor leather releases toxic gas.