ERDGuide rail type lifting cargo elevatorsincere service

Are the water cooling and air cooling of the hydraulic station the same?Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .ERD, 'Elevator Supervision and Inspection Regulations' 'Elevator Maintenance Rules' (GB and related national standards, industry standards and local standards.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements,ERDOutdoor cargo elevator, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Al Ghaydah,The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.

Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Based on the information you have investigated, choosing a lifting machine with better cost performance should be based on its technical parameters, practicability and versatility. Usually, there are many kinds of aluminum alloy lifting machines, including vehicle-mounted lifts, hydraulic lifts, scissor lifts, etc. each have slightly different technical parameters and uses, but there are also many similar functions. Therefore, as a customer, you have to choose with a purpose, you buy a mechanical lift What to do, and which kind of lifting machinery can meet your needs and has multiple uses. The last point is that after the equipment arrives when unpacking and accepting, check whether the accompanying technical information is complete, whether the accompanying accessories, tools, and accessories are consistent with the list, and whether the equipment and Check whether the accessories are damaged, defective, etc., and make a record of unpacking and acceptance. The working principle of the aluminum alloy elevator: the hydraulic oil is formed by the vane pump to a certain pressure, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve hydraulic control check valve, and balance valve, and the oil returned from the upper end of the hydraulic cylinder returns to the fuel tank through the explosion-proof electromagnetic reversing valve. The rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.Installation works,Unscrew the screw on the dust-proof hole outside the flange of the elevator,ERD5 ton cargo elevator, adjust the PCS system ring to align the side hole with the dust-proof hole and tighten the inner hexagon. After that, remove the motor shaft key.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Where can I find it?,Are the water cooling and air cooling of the hydraulic station the same?theIt has been inspected and debugged, and all technical indicators have met the design requirements. When using it, it only needs to be connected to the power supply, and the hydraulic and electrical systems do not need to be adjusted.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.ERDRegarding the cleanliness of the hydraulic station, is there any relevant rule requirement?In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft,ERDGood comments on cargo elevators, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.