SaskatoonUsed pipeline pumpOther basic functions and features

　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor andSaskatoon,　　 Damage of mechanical seal the material of mechanical seal is generally Cr or L, which is relatively rigid, not flexible and vulnerable. The installation of mechanical seal is that the static ring is fixed outside, and the moving ring is fixed with the pump shaft. When the slurry pump reverses, and the impeller retreats　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that,SaskatoonSubmersible pump can pump sewage, cut off the power supply of the motor. If the temperature of the environment is low open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃,SaskatoonISG single stage vertical pipeline pump, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyWellington,　　 if the removed gasket is seriously damaged a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump

　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　Put it into water for use.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.Word of mouth recommendation, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　The whole packing body,SaskatoonSubmersible sewage pump, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.High quality and low price,　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　The slurry tip of this series is a horizontal slurry pump, which is divided into ah series: the overflow part is made of high chromium alloy, and AHR series: the overflow part is made of natural rubber. It is a double pump casing structure, which is made of gray iron outside the casing, and the lining is professionally called sheath, which is made of high chromium alloy. If AHR series　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.Saskatoon, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, and use the PID adjustment of the frequency converter. When